Industrial Catalog 08

and others working around you, can be seriously injured by fastener driving tools if you do not follow the instructions provided on the tool and in the operator 9s manual.<br><br> Used properly, these tools provide easy, safe, and efficient methods for driving nails and staples for all kinds of construction projects. REFER to your Operator 9s Manual, Parts List, or call Bostitch ® Customer Service at: 1-800-556-6696 if any of the terms used below are unfamiliar to you. EYE PROTECTION which conforms to ANSI Z87.1 specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when connecting to air supply, loading, operating or servicing this tool.<br><br> Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury. THE CONTACT OR SEQUENTIAL TRIP Bostitch offers two types of triggers for pneumatic tools: Contact Trip (black trigger) and Sequential Trip (silver-gray trigger). Each trigger has specific advantages.<br><br> For example,theContactTripisbestsuitedforhigh-volume,rapidnailingorstaplingwhere exact placement of the fastener is not important. The Sequential Trip is best suited for applications where rapid nailing is not required orwheretheexactplacementofthefastenersisimportant.Youshouldevaluateyour construction project to determine which trigger type is best for you. CONTACT TRIP A Bostitch ® tool with the Contact Trip (black trigger) will drive a nail whenever both the trip and the trigger are depressed at the same time.<br><br> The tool can be used to rapidly drive nails by holding the trigger pulled and repeatedly bumping the trip against the work to be nailed (Bump Firing). A nail is driven each time the trip is bumped against the work. The Contact Trip (black trigger) will not prevent a nail from being accidentally driven if the trigger is held, pulled and the trip is bumped against any object or person.<br><br> Never hold or carry the tool with your finger on the trigger unless driving fasteners. The Contact Trip (black trigger) can also be operated by holding the tool against the work with the trip depressed and then pulling the trigger (Place Nailing). When using a Contact Trip for Place Nailing, the tool may bounce due to recoil, and if the tool is allowed to recontact the work surface while you are holding the trigger, a second nail will be driven.<br><br> The operator should allow the tool to recoil far enough to release the trip and avoid a second cycle. Don 9t push the tool down extra hard; let the tool do the work. SEQUENTIAL TRIP The Sequential Trip (silver-gray trigger) offers a positive safety advantage since it will not accidentally drive a nail if the tool is bumped against any surface or while the operator is holding the tool with the trigger pulled.<br><br> It also allows Place Nailing without the possibility of driving a second nail on recoil as described under cContact Trip. d The Sequential Trip (silver-gray trigger) gets its name from the csequence d required to operatethetool.Todriveanail,theoperatormustfirstdepressthetripagainstthework and then pull the trigger. To drive a second nail, the operator must lift the tool from the work, release the trigger, and then repeat the above sequence. If further information is required, call Bostitch ® Customer Service at 1-800-556-6696 or write to: Bostitch ® Customer Service, 1 Briggs Drive, East Greenwich, RI 02818.<br><br> WHO IS We work hard to maintain our position as the market leader. That's a tradition that Thomas Briggs, our founder, started when he invented the world's first stapler back in 1896. Over 110 years later, the spirit of quality&innovationlivesonineverythingwedo-fromfieldresearchto new product development.<br><br> Whether it's the introduction of the world's firstcollatedstapleorthenewStrapshot" metalconnectornailer, onethingremainstrue& BOSTITCHisindeedtheauthenticfastenerbrand. BOSTITCH? We strive to meet a higher standard.<br><br> For example, our award-winning HurriQuake " nail is proven to be up to 2x's more resistant to hurricane winds. According to Popular Science magazine, this unique breakthrough can save millions of dollars and thousands of lives. Our passion for excellence makes us better & each one of our 1,300 employees are determined to make a difference and improve the way work is to be done.<br><br> We are BOSTITCH. And Proud of it. Why Does It Pay to Have a Fat Head?<br><br> Patented Fat Head 19% larger than standard nails, providing maximum shear and pull-through resistance Advanced dNo Void d Shank Technology Deep screw shank results in maximum withdrawal performance PalletPlus " Revolutionary Nail Technology Now that 9s innovation from BOSTITCH ® PALLETS, CRATING, FENCING Precision Point Reduces splitting in hardwoods 264% More Protection from End Board Impact 40% Greater Shear Resistance 35% Increase in Withdrawal Performance 17% Increase in Diagonal Rigidity 15% Greater Resistance to Pull-Through PALLETS, CRATING, FENCING 5 Great Product Lines Featuring Fat Head" Technology Pallet Plus " .084 d Collated Nails Your replacement for standard .099 d pallet nails. Our patented nail geometry delivers equivalent performance to standard .099 d pallet nails using a shorter and thinner nail. Also take advantage of the 20% lighter N64084 tool.<br><br> " Equal Performance vs. Standard .099 d Collated Pallet Nails " Use a Lighter Tool " Increase Productivity " Reduce Operator Fatigue Pallet Plus " .099 d Collated Nails Best-in-class performing .099 d pallet nails. Our patented geometry delivers equivalent performance to standard .113 d pallet nails.<br><br> Your replacement for .105 d or .113 d collated nails used for new pallet construction or repair. " Equal Performance vs. Standard .113 d Collated Pallet Nails " More Trips Until Repair vs.<br><br> Standard .099 d Nails " More Durable Pallet " Increase Customer Satisfaction Pallet Plus " .105 d BULK Nails Your replacement for standard .113 d bulk nails. Our patented nail geometry delivers equivalent performance to standard .113 d bu lk nails. You can build up to 27 more pallets per box which equates to over 19,000 more pallets per truckload of nails.<br><br> " Equal Performance vs. Standard .113 d Bulk Nails " Value-Added Performance " Build 20% More Pallets per Box Block Mat Nails: .099 d Wedge Grip " Pallet Plus Your replacement for standard .135 d block mat nails. Utilizing both patent pending Wedge Grip" and patented Fat Head" technologies, this nail delivers ultimate deck mat performance using four nails per joint.<br><br> " One More Pallet Trip Until Repair " 37% Greater Withdrawal Resistance per Joint " Reduce Wood Splitting Fencer Plus " .084 d Wedge Grip " Collated Nails Your replacement for standard .090 d fencing nails. Utilizing both patent pending Wedge Grip" and patented Fat Head" technologies, this nail delivers ultimate performance in wood fences. ThickCoat" galvanized for protection against the most corrosive pressure treated lumbers.<br><br> " Equal Performance vs. Standard .090 d Fencing Nails " Reduce Wood Splitting " ThickCoat" Galvanization (approved for ACQ lumber) We pack about 1,500 more nails into our boxes than the competition. More nails = more pallets.<br><br> There 9s a quality Bostitch ® fastener for every application. Check out our Fastener - Tool Selection Guide on pages 46-51 in the back of the catalog. 750S4 Reattaching Deck Board Pallet Repair and Assembly: N58C-1 N64084-1 N64099-1 N89C-1P N70CB N80CB N400C-1 750S4 750S5 850S4 CF15-2 Machine mount version and remote trigger valves are available.<br><br> Consult your representative or factory. Bostitch offers an extensive line of hard-working, long-lasting industrial strength pneumatic tools. CF15-2Pneumaticcorrugatedtool repairingsplitstringer (seealso538S21414-gauge stapler, p.<br><br> 23) 8 Work Safely with Tools, Wear Safety Glasses. For more information on contact, sequential, trigger operated or auto fire see sa fety information on page 5. PALLETS, CRATING, FENCING Crate Assembly: N58C-1 N89C-1P N64 SX150 538S4 538S5 750S4 750S5 850S4 Machine mounted nailer applying Fencer Plus " Nails N58C Coil nailer fastening fence header board N400C-1 Nailing mat to block pallet Fence Assembly: N58C-1 N64 N80CB HFP9 (see also page 42 of specialty fencing selection) 9 Work Safely with Tools, Wear Safety Glasses.<br><br> For more information on contact, sequential, trigger operated or auto fire see saf ety information on page 5 750S4 Assembling crate face-frame PALLETS, CRATING, FENCING HFP9 Attaching tensioning wire to chainlink fence with 9 gauge aluminum hog rings N58C-1 Box Frame Nailer Features: " Uses wire collated nails " Durable cast aluminum frame and cap " Oversized canister opens completely for fast Applications: " Pallets assembly and repair " Fence panel assembly " Crate assembly Tool Description: " Tool Weight: 5.7 lbs. " Driving Power: 445 inch lbs. @ 100 psi " Magazine Capacity: 300 to 350 depending on nail size " 1 d to 2-1/4 d inch (2d to 7d) N64084-1, N64099-1 (restricted tool) Pallet, Crate, Fence Nailer Features: " Uses wire collated nails " .084" model has oversized bore for driving .084" Pallet Plus nails " .099" model has oversized bore for driving .099" Pallet Plus and WB nails " Oversized canister opens completely for easy reloading " Tool-free adjustable exhaust Applications: " Crate frames, medium duty pallet assembly and repair " Fence panel assembly " Picket assembly using aluminum nails Tool Description: " Tool Weight: 6.1 lbs.<br><br> " Driving Power: 560 inch lbs. @ 100 psi " Magazine Capacity: 225 to 350 depending on nail size " 1-1/4 d to 2-1/2 d (3d to 8d) N70CB (restricted tool) Heavy Duty Pallet Nailer Features: " Uses wire collated nails " Angled coil design for high operator visibility " Quick loading canister " Better balance for operating ease Applications: " Heavy duty pallet assembly Tool Description: " Tool Weight: 7.9 lbs. " Driving Power: 738 inch lbs.<br><br> @ 100 psi " Magazine Capacity: 225 to 300 depending on nail size " 1-1/2 d to 2-3/4 d (4d to 9d) N80CB, N89C-1P Heavy Duty Pallet, Fence Nailer Features: " Quick open canister " Rubber comfort grip " Drives wire collated nails .099"-.148" Applications: "Heavydutyblockpalletassembly "Heavydutypicketfenceassembly Tool Description: " Tool Weight: 8.4 lbs. / 8.1 lbs. " Driving Power: 880 inch lbs.<br><br> / 1050 inch lbs. " Magazine Capacity: 225 to 300 depending on nail size N400C-1 (restricted tool) Hardwood Pallet, Crate Nailer Features: " Drives wire collated nails from .099" to .148" in diameter " Secondary handle, rubber grip and integral balancer mounting point in cap Applications: " Block pallet assembly " Hardwood Crate and Pallet Assembly Tool Description: " Tool Weight: 11.6 lbs. " Driving Power: 1450 inch lbs.<br><br> @ 100 psi " Magazine Capacity: 225 to 300 depending on nail size Available in: Plain, galvanized, stainless steel, aluminum** **Aluminum nails require door conversion kit (Item#112670) Available in: Plain, galvanized, stainless steel 15ÚCoil Nail REFER TO AC, C AND FC SERIES ON PAGES 46- 48 REFER TO AC, C, ACP AND FC SERIES ON PAGES 46-48 REFER TO AC, C, FC, FC PALLET PLUS SERIES ON PAGES 46-48 REFER TO AC, C, FC, FC PALLET PLUS SERIES ON PAGES 46-48 REFER TO AC, C AND FC SERIES ON PAGES 46-48 15ÚCoil Nail Available in: Plain, galvanized, stainless steel Available in: Plain, galvanized, stainless steel, aluminum Ring Screw Available in: Plain, galvanized, stainless steel, aluminum** **Aluminum nails require door conversion kit (Item#112670) PALLETS, CRATING, FENCING 10 Work Safely with Tools, Wear Safety Glasses. For more information on contact, sequential, trigger operated or auto fire see sa fety information on page 5. PALLETS, CRATING, FENCING HFP9 Wire Fence Tool Features: " Allows collated hog rings to feed directly into the jaws " Magazine pivots, allowing the tool to reach into difficult areas to fasten tension wire Applications: " Fastening tensioning wire, signs to fence, stitching butt ends, and repair Tool Description: " Tool Weight: 1.2 lbs.<br><br> " Magazine Capacity: 25 rings CF15-2 Pallet Stringer Repair Features: " Powerful to provide full penetration of stringers Applications: " Repairing and strengthening split pallet stringers Tool Description: " Tool Weight: 6.58 lbs. " Driving Power: 433 inch lbs. " Magazine Capacity: 108 REFER TO #8 ON PAGES 54 & 55 REFER TO PAGE 49 Available in: Aluminum 538S4, 538S5 Medium Duty Crate Stapler Features: " Anti-Jam TM magazine permits staples to exit nose without jamming " Long narrow nose for improved line of sight " Adjustable trip for positive staple depth control " Long magazine kit available: 108xxx , p.60 Applications: " Light and medium duty crate framing and sheathing Tool Description: " Tool Weight: 4.7 lbs.<br><br> "DrivingPower: 260inchlbs. @100psi " Magazine Capacity: 160 " Long Magazine: 300 + " S4: 3/8" to 1-1/2 d inch leg " S5: 1/2" to 2 d inch leg REFER TO 16S4, S5 STAPLES ON PAGE 50 16-Gauge S4 Staple 750S4, 750S5, 850S4 Heavy Duty Pallet, Crate Stapler Features: " Anti-Jam TM breathing magazine permits staples to exit nose without jamming " Long magazine kit available: 108xxx, p.60 Applications: " Heavy duty pallet manufacturing and repair " Heavy duty crate framing Tool Description: 750S4-S5 " Tool Weight: 5.3 lbs. "DrivingPwr: 465inchlbs.<br><br> @100psi " Magazine Capacity: 160 " Long Magazine: 300 + " S4 and S5: 1-1/2 d to 2 d inch leg 850S4 " Tool Weight: 5.9 lbs. " Driving power: 570 inch lbs. " Magazine Capacity: 160 " Long Magazine: 300 + " 1-1/2" to 2 d inch leg REFER TO 16S4, S5 STAPLES ON PAGE 50 16-Gauge S4 Staple RING09AL25 16-Gauge S5 Staple 16-Gauge S5 Staple 750 Also for stringer repair see 14-gauge Wide Crown Stapler 538S214 page 21 REFER TO THE TOOL & ACCESSORY PART NUMBER GUIDE ON PAGES 56 & 57.<br><br> Corrugated 11 Work Safely with Tools, Wear Safety Glasses. For more information on contact, sequential, trigger operated or auto fire see saf ety information on page 5. 850 UPHOLSTERED FURNITURE Furniture Frame Assembly: 538S4 538S5 650S4 650S5 Spring Assembly: 438S5 AK Automatic AK Semi Automatic TRK Automatic TRK Semi Automatic HR-65C-130 HR-66C-110 Trim Assembly: SX150 BT125 BT200 S32SX BT35B BT50B N62FN N52FN Fabric to Wood: 21671B 21671B-A 21671B-ALM 21671B-LN 21680B 21680B-LN 21697B LockNail TM System Packaging: 450S2 538S4 Stapler applying staples during knock-up Sinuousspring anchorclip applicationtochair railw/AK Machine 438S5 Stapler applying anchor clip to chair rail There 9s a quality Bostitch ® fastener for every application.<br><br> Check out our Fastener - Tool Selection Guide on pages 46-51 in the back of the catalog. To increase productivity, it takes a quality craftsman and the right tool for the right job. Bostitch is your partner every step of the way.<br><br> Fabric to Wire: TR201 TR203 TR315 12 Work Safely with Tools, Wear Safety Glasses. For more information on contact, sequential, trigger operated or auto fire see sa fety information on page 5. HR-66C-110 Clip Tool connecting tie wire to sinuous springs LockNail TM Machine applying LockNail TM to upholstered panel 21671B Upholstery Tacker fastening fabric to seat cover with 71 series fine wire staples 13 Work Safely with Tools, Wear Safety Glasses.<br><br> For more information on contact, sequential, trigger operated or auto fire see saf ety information on page 5. UPHOLSTERED FURNITURE AK/TR Semi Automatic, AK/TRK Automatic Spring Clip to Rail Application Features: AK Semi Automatic: HR-55740 TRK Semi Automatic: HR-57129 " Allows precision placement of spring anchor clips to chair rail (straight or curved) for uniform spring alignment and ride " Coil-fed anchor clip system " Operator-fed single piece operation Applications: " Chair/loveseat/sofa frame rail spring clip application " For best results, it is recommended that all clips be hammer closed after spring up AK Automatic: 169601 TRK Automatic: HR-57130 " Machine includes: clipping head, ejector block, control box, translator, drive system, air system, pusher arm, sensor assembly " End exit hold down, exit cover are available Features: " Electric multi-rail autofeed mechanism " Low skill level 8000 clip/hr operation " Store and Transfer Rail set-up offline via ethernet Applications: " Low volume over-the-rail spring clip placement or applications using plywood back posts Tool Description: " Tool Weight: 4.7 lbs. " Magazine Capacity: 168 Staples " Staple: 16 S5 Series, 1/2 d to 1-1/2 inch leg Also Available: 438S5CLPSKIT- For front magnet and steel stop for clip alignment.<br><br> 438S5CLPTBKIT- For front and back magnets for top and bottom clip alignment. 438550SKCLPKIT- For long nose clips. See page 156 438S5 Clip Kit Spring Anchor Clip Stapler Features: " Ability to load OSK clip into tool prior to stapling " Magnetic nose holds OSK clip in place for precise alignment of staple legs over clip holes " Attachment of other sinous spring clips to frame seat and back rails OSK Clip " Polypropylene lined " Edge embossed Applications: " Attach steel bands to seat rails to support coil springs in 8-way hand tie " Plywood frame assembly Tool Description: " Tool Weight: 4.7 lbs.<br><br> " Driving Power: 260 inch lbs. @ 100 psi " Magazine Capacity: 160 " S4: 3/8 d to 1-1/2 inch leg " S5: 1/2 d to 2 inch leg 438S5, 538S4, 538S5 FRAME ASSEMBLY Features: " Anti-Jam TM magazine feeds staples without jamming " Long narrow nose for increased visibility " Adjustable trip for positive staple depth control " Long magazine kit available: 108xxx, p.60 HR-65C-130, HR-66C-110 Spring Clipping Tools Features: " Surface clinching tool squeezes instead of folding the clip around wires " Driver blade cleanly picks up a clip from the magazine, places it around the wires, and forms the clip into a tight, strong wire bond Applications: HR-65C-130: " Clipping smaller gauge sinuous spring to tie wire REFER TO REGULAR AND CUSHION CLIP SECTION ON PAGE 53 16-Gauge S4 Staple 16/17-Gauge S5 Staple For Spring to Tie Wire sizing, refer to the Sinuous Spring application chart on Pg 43 REFER TO 16 S4, S5 SERIES ON PAGE 50 HR-AK-1EW HR-TRK HR-AK-2, AK-3, AK-4 HR-OSK REFER TO 16 S5 SERIES ON PAGE 50 SPRING ANCHOR CLIPS (OSK) ON PAGE 52 REFER TO SPRING ANCHOR CLIPS PAGE 52 Width Crown Diameter (opening) Height Semi-Automatic HR55740 Automatic 14 Work Safely with Tools, Wear Safety Glasses. For more information on contact, sequential, trigger operated or auto fire see sa fety information on page 5.<br><br> Applications: HR-66C-110: " Clipping larger gauge sinuous seat and back springs to stabilizing tie wire " Clipping coil seat springs to border wires in 8-way hand tie upholstered unit application Tool Description: " Clinching Power: 2000 lbs. " Magazine Capacity: 25 to 45 collatedclips " Regular and noise reducing (paper lined) Cushion Clips UPHOLSTERED FURNITURE 650S4, 650S5 Furniture Frame Construction Features: " Anti-Jam" " Increased power to countersink staples into hardwood " Overmolded rubber comfort grip " Long narrow nose for improved line of sight in precise applications Applications: " Furniture frame knock up Tool Description: " Tool Weight: 4.5 lbs. " Driving Power: 340 inch lbs.<br><br> @ 100 psi " 650S4 Magazine Capacity: 160 " 650S5 Magazine Capacity: 171 " 1 to 2 inch leg TR201, TR203, TR315 Attach Edge Roll to Border Wire Features: " TR201 Spring returned tool " TR203 Spring returned tool long mag. " TR315 High Speed air return, long mag. Magazine can be pivoted in 90Ú increments Applications: " Attaching edge roll to border wire Tool Description: " 15 ga.<br><br> 3/4 D ring, 1/4 inch min. closure " Short Magazine: 50 rings, 3.3 lbs. " Long Magazine: 100 rings, 3.6 lbs.<br><br> LockNail TM System, HR-LN Securing Upholstered Panels to the Frame Features: " The LockNail TM system is an upholstery panel system that is designed to secure hard galvanized steel fasteners to cardboard or composite panels. After this 'pre-nailing', padding and cover are applied, then the panel can be securely nailed to furniture frame using a mallet. Applications: " Securing upholstery panels to the frame Material Thickness: .180 Max, CardBoard .094 Max, Chip Board .094 Max, Plywood Available in: Coated Available in: Basic Steel, galvanized, stainless S32SX, S32SL, SX150, SL150 ProductionFinishandTrim Stapler Features:S32SX,S32SLExtremeDuty: " Extreme-duty,highcycledesign(requiresoil) " Compositeframe/Aluminummagazine " Narrownoseforimprovedlineofsight Features:SX150,SL150OilFree: " Oil-freeengine " Magnesiumframecompositemagazine " Narrownoseforimprovedlineofsight " Ultra-quiet,rearexhaust " Auto-fireoptions:BTSXAF-125-KIT andBTSXAF-200-KIT " Longmagazineversions(2xcapacity) SX150LM,SL150LM Applications: " High production finish and trim " Frame assembly - corner blocks, stretchers Tool Description: S32SX " Tool Weight: 2.4 lbs.<br><br> "Driving Pwr: 145inch lbs. @100psi S32SL " Tool Weight: 2.5 lbs. "Driving Pwr: 160inch lbs.<br><br> @100psi SX150 " Tool Weight: 2.5 lbs. "Driving Pwr: 170inch lbs. @100psi SL150 " Tool Weight: 2.5 lbs.<br><br> "Driving Pwr: 170inch lbs. @100psi REFER TO 16 S4, S5 SERIES ON PAGE 50 REFER TO LOCKNAIL TM SECTION ON PAGE 52 REFER TO #5 ON PAGES 54 & 55 REFER TO SX SERIES ON PAGE 51 Applications: " Decorative molding, fine trim work Tool Description: BT35B " Tool Weight: 2.4 lbs. " Driving Pwr: 145 inchlbs.@100psi BT125 " Tool Weight: 1.9 lbs.<br><br> " Driving Pwr: 145 inchlbs.@100psi BT50B " Tool Weight: 2.6 lbs. " Driving Pwr: 165 inchlbs.@100psi BT200 " Tool Weight: 2.1lbs. " Driving Pwr: 170 inchlbs.@100psi BT35, BT50, BT125, BT200 Decorative Trim, Corner Block Nailer Features:BT35B,BT50BExtremeDuty " Extreme-duty,highcycledesign(requiresoil) " Compositeframe/Aluminummagazine " Narrownoseforimprovedlineofsight Features:BT125,BT200Oil-free " Oil-freeengine " Magnesiumframecompositemagazine " Narrownoseforimprovedlineofsight " Ultra-quiet,rearexhaust " Auto-fireoptions:BTSXAF-125-KITand BTSXAF-200-KIT REFER TO BT SERIES ON PAGE 47 16-Gauge S4 Staple 18-Gauge SX Staple locknail Self-locking tabs 15-Gauge D-Ring 16/17-Gauge S5 Staple HR-LN2 HR-LN3 REFER TO THE TOOL & ACCESSORY PART NUMBER GUIDE ON PAGES 56 & 57.<br><br> 18-Gauge Brad 13/8 d 15 Work Safely with Tools, Wear Safety Glasses. For more information on contact, sequential, trigger operated or auto fire see saf ety information on page 5. UPHOLSTERED FURNITURE Applications: " Securing fabric to wood frame " Pre-upholstery spring-up operation attach cardboard, webbing, Propex to frame " Boat seating with stainless steel staples Tool Description: 21671B " Tool Weight: 1.8 lbs.<br><br> " Magazine Capacity: 196, 71 series staples 21697B " Tool Weight: 1.9 lbs. " Magazine Capacity: 156, 97 series staples 21671B-LN " Tool Weight: 2.1 lbs. " Magazine Capacity: 196, 71 series staples 21671B-A " Tool Weight: 2.6 lbs.<br><br> " Magazine Capacity: 196, 71 series staples 21671B-ALM " Tool Weight: 3.0 lbs. " Magazine Capacity: 392, 71 series staples 21680B, 21680B-LN, 21680B-ALM " Tool Weight: 1.8 lbs. " Magazine Capacity: 156, 80 series staples 216Series Fabric to Wood Assembly Features: 21671B: " Very lightweight, rugged, all metal construction, quiet, low air consumption 21671B-LN: " Same as 21671B but with extended nose for greater visibility and access to hard-to-reach areas " Long nose also helps prevent scarring andscratching of wood 21671B-A: " 2-function trigger light squeeze for single fire mode; full squeeze for auto-fire mode " Auto fire rate can be adjusted from 0 to 1600 staples/minute " Same hand that activates trigger also opens magazine, allowing for new staple insertion with the free hand 21671B-ALM: " Same as 21671B-A but w/long magazine (392 Staples) 21680B, 21680B-LN (long nose) "Sameas21671Bbutfires80seriesstaples " 21697B Attaching double welt N62FN, N52FN Decorative Trim Nailer Features: N62FN: " Oil free engine requires no lubrication and leaves no oil stains on work " Tool-free removable magazine for fast cleaning and jam clearing Applications: " Decorative trim, finished wood panels Tool Description: N62FN, N52FN: " Tool Weight: 3.8 lbs.<br><br> " Driving Power: 400 inch lbs. @ 100 psi " Magazine Capacity: 100 Also see straight 16-Gauge finish nailer FN16250 on page 32. Available in: Coated, stainless steel, aluminum 450S2 Applications: " Furniture packaging: corrugated boxes to wood " Frame Assembly, bridge joints Tool Description: " Tool Weight: 4.6 lbs.<br><br> " Driving Power: 230 inch lbs. @ 100 psi " Magazine Capacity: 160 " 1/2 to 2 inch leg REFER TO 16 S2 SERIES ON PAGE 50 Available in: Coated 15-Gauge Finish Nail 16-Gauge S2 Staple REFER TO 71, 80 SERIES ON PAGES 50 71 Staple 80 Staple REFER TO FN15 SERIES ON PAGE 48 REFER TO THE TOOL & ACCESSORY PART NUMBER GUIDE ON PAGES 56 & 57. 97 Staple Furniture Packaging / Frame Assembly Stapler Features: " Lightweight durable aluminum frame " Anti-Jam magazine " Power control valve, adjusts power by 30% " Overmolded rubber comfort grip " Reduced height for stapling in tight areas " Rear exhaust directs exhaust away from user and work surface " High capacity, top-load magazine decreases reload time " ESD-450S2-WS 450S2 with 22 1/2" extended handle available for easy fastening of boxes to pallets 16-Gauge Finish Nail 16 Work Safely with Tools, Wear Safety Glasses.<br><br> For more information on contact, sequential, trigger operated or auto fire see sa fety information on page 5. CASE GOODS CASE GOODS CF15 Applying corrugated fastener to an angled butt joint 1 1 2 2 3 3 4 4 5 5 6 6 There 9s a quality Bostitch ® fastener for every application. Check out our Fastener - Tool Selection Guide on pages 46-51.<br><br> 750S4 750S5 438S2 CF152 HP118K TU-225-18HP 438S4 MCF16 650S4 650S5 BA-T156 N62FN FN16250 S32SL S32SX S3297 18-gauge SX staples building drawers 18-gauge brads fastening quarter round Caseback being secured with 18-gauge SL staples 18-gauge brads applying trim 16-gauge nails securing a cabinet face 17 Work Safely with Tools, Wear Safety Glasses. For more information on contact, sequential, trigger operated or auto fire see saf ety information on page 5. SX150 SL150 N52FN BT-35B BT50B BT125 BT200 CASE GOODS 750S4, 750S5 Heavy Duty Assembly Stapler Features: " Powerful engine for driving into hardwood " Anti-Jam TM breathing magazine permits staple to exit nose without jamming " Long narrow nose for improved line of sight " Adjustable trip for positive staple depth control " Multi direction exhaust and comfort grip Applications: " Heavy duty structural assembly Tool Description: " Tool Weight: ~5.3 lbs.<br><br> " Driving Power: 465 inch lbs. @ 100 psi " Magazine Capacity: 160 " Long Magazine: 300 + " 1-1/2 to 2 inch leg Available in: Coated REFER TO 16 S4, S5 SERIES ON PAGE 50 REFER TO 16 S2, S4 SERIES ON PAGE 50 REFER TO 97 SERIES ON PAGE 50 Available in: Coated Applications: " Decorative molding, fine trim work " Drawer blocks, bottoms, guides Tool Description: " Tool Weight: 2.5 lbs. " Driving Power: 160 inch lbs.<br><br> @ 100 psi " Magazine Capacity: 100 S3297 Decorative Molding, Fine Trim Stapler Features: " Lightweight ergonomic, designed handle " Fast trigger stroke Applications: " S2 Packaging, corrugated containers to pallets " S4 Corner connections, frames Tool Description: S2 " Tool Weight: 4.5 lbs. " Driving Power: 230 inch lbs. @ 100 psi " Magazine Capacity: 160 " 1/2 to 1-1/2 inch leg S4 " Tool Weight: 4.05 lbs.<br><br> " Driving Power: 230 inch lbs. @ 100 psi " Magazine Capacity: 160 " 1/2 to 1-1/2 inch leg 438S2, 438S4 Packaging, Corner Connection Stapler Features: " Lightweight, molded lifetime comfort grip, reduced height for work in tight areas " 30% adjustment in power with turn of valve " Rear exhaust directs exhaust away from user and work surface " Adjustable trip-positive staple depth control 16-Gauge S2 Staple 16-Gauge S4 Staple Applications: " Door and window frames Tool Description: " Tool Weight: 4.5 lbs. " Driving Power: 340 inch lbs.<br><br> @ 100 psi " Magazine Capacity: S4: 160, S5: 171 " 1 to 2 inch leg 650S4, 650S5 Door, Window Frame Stapler Features: " Increases power to countersink staples into dense hardwood " Long narrow nose for improved line of sight " Overmolded rubber grip maximizes comfort " Adjustable exhaust directs exhaust away from user " Adjustable depth guide Available in: Coated 16-Gauge S4 Staple 16-Gauge S5 Staple 20-Gauge 97 Staple 16-Gauge S4 Staple Available in: Coated REFER TO 16 S4, S5 SERIES ON PAGE 50 16-Gauge S5 Staple 438S4 Shown 18 Work Safely with Tools, Wear Safety Glasses. For more information on contact, sequential, trigger operated or auto fire see sa fety information on page 5. CASE GOODS REFER TO SX, SL SERIES ON PAGE 51 Applications: " Trim work, drawers, cabinets Tool Description: " Tool Weight: 3.8 lbs.<br><br> " Driving Power: 400 inch lbs. @ 100 psi " Magazine Capacity: 130 " 1 to 2-1/2 inch 15-ga. Finish nail N62FN, N52FN Trim Work, Drawers, Cabinet Nailer Features: " Oil-free engine requires no lubrication " Tool-free removable magazine Also see page 32, FN16250 16-gauge straight finish nailer.<br><br> Available in: Coated, stainless steel, aluminum REFER TO FN15 SERIES ON PAGE 48 REFER TO BT SERIES ON PAGE 47 REFER TO CORRUGATED FASTENERS SECTION ON PAGE 49 REFER TO 18-GA & 23-GA HEADLESS PIN SECTION ON PAGE 49 15-Gauge Finish Nail S32SX, S32SL, SX150, SL150 Applications: " SX Trim work, drawers, cleat attachment, pin tenon joints, drawer stop blocks " SL Case backs, metal guides Tool Description: S32SX " Tool Weight: 2.5 lbs. " Driving Pwr: 160 inch lbs. @ 100 psi SX150 " Tool Weight: 2.5 lbs.<br><br> " Driving Pwr: 170 inch lbs. @ 100 psi S32SL " Tool Weight: 2.5 lbs. " Driving Pwr: 160 inch lbs.<br><br> @ 100 psi SL150 " Tool Weight: 2.5 lbs. " Driving Pwr: 170 inch lbs. @ 100 psi Available in: Coated Applications: " Decorative molding, fine trim work " Drawer; pinning French and other dovetail joints Tool Description: BT35B " Tool Weight: 2.4 lbs.<br><br> " Driving Pwr: 145 inchlbs.@100psi BT125 " Tool Weight: 1.9 lbs. " Driving Pwr: 145 inchlbs.@100psi BT50B " Tool Weight: 2.6 lbs. " Driving Pwr: 165 inchlbs.@100psi BT200 " Tool Weight: 2.1lbs.<br><br> " Driving Pwr: 170 inchlbs.@100psi BT35B, BT50B, BT125, BT200 Extremer Duty Decorative Molding, Fine Trim Nailer Features BT35B, BT50B Extreme Duty: "Extreme-duty,highcycledesign(requiresoil) "Compositeframe/Aluminummagazine " Narrow nose for improved line of sight Features BT125, BT200 Oil-free: "Oil-freeengine "Magnesiumframecompositemagazine " Narrow nose for improved line of sight "Ultra-quiet,rearexhaust "Auto-fireoptions:BTSXAF-125-KIT andBTSXAF-200-KIT Available in: Coated Applications: " Decorative molding, fine trim Tool Description: TU-225-18HP (18-GAUGE) " Tool Weight: 2.3 lbs " Magazine Capacity: 230 HP118K (23-GAUGE) " Tool Weight: 2.3 lbs " Magazine Capacity: 230 TU-225-18HP, HP118K Features: " Adjustable high/low power control " Lightweight, durable aluminum housing " Overmolded grip " Rear exhaust 23-Gauge Headless Pin Tool Description: CF15 " Tool Weight: 6.58 lbs. " Magazine Capacity: 128 MCF16 " Tool Weight: 4.75 lbs. " Magazine Capacity: 156 CF15, MCF16 Door, Cabinet Mitre Nailer Features: " Lightweight Applications: " Joining door stiles, cabinet face frames " Stile assembly, door window fabrication Corrugated For: CF15 18-Gauge SX Staple REFER TO THE TOOL & ACCESSORY PART NUMBER GUIDE ON PAGES 56 & 57.<br><br> 18, & 23-Gauge Headless Pinner Trim Work Cabinet Case Stapler Features S32SX, S32SL Extreme Duty: "Extreme-duty,highcycledesign (requiresoil) "Compositeframe/Aluminummagazine " Narrow nose for improved line of sight FeaturesSX150,SL150Oil-free: "Oil-freeengine "Magnesiumframecompositemagazine " Narrow nose for improved line of sight "Ultra-quiet,rearexhaust "Auto-fireoptions:BTSXAF-125-KIT andBTSXAF-200-KIT "Longmagazineversions(2xcapacity) SX150LM,SL150LM 18-Gauge Brad 13/8 d 16-Gauge Finish Nail 19 Work Safely with Tools, Wear Safety Glasses. For more information on contact, sequential, trigger operated or auto fire see saf ety information on page 5. 18-Gauge Headless Pin For: MCF16 MANUFACTURED HOUSING Fast, accurate, cost-effective manufactured housing relies on Bostitch ® tools and fasteners.<br><br> Framing F21PL F28WW N80CB MCN150 640S4 BIGBERTA160-2 538S214-1 Flooring / Underlayment 863S4 S32SX S32SL Sheathing / Siding N58C F21PL F28WW N80CB SB150SLBC 538S4 Roofing 450S2 RN46 438S2R US056 SB150SLBC Cabinet / Trim BT35B BT50B N62FN S32SX N52FN BT125 BT200 There 9s a quality Bostitch ® fastener for every application. Check out our Fastener - Tool Selection Guide on pages 46-51. 538S214-1 With 14-gauge staples stitching truss joint and truss plate prior to roller press F28WW Assembling 2" x 4" stud wall 863S4 538S214 F33PT MCN250 650S4 650S5 750S5 USO56-1 650S414Kit N66BC 20 Work Safely with Tools, Wear Safety Glasses.<br><br> For more information on contact, sequential, trigger operated or auto fire see sa fety information on page 5. SX150 SL150 F21PL FRAMING NAILER N66C Applying C4DCSBALG Ballistic Point Nail to steel stud MCN150 Fastening Hurricane Strap to framing joists 21 Work Safely with Tools, Wear Safety Glasses. For more information on contact, sequential, trigger operated or auto fire see saf ety information on page 5.<br><br> MANUFACTURED HOUSING F28WW Stick Framing Nailer Features: " Patented push-button adjustable depth guide " Lightweight magnesium design for durability " Aggressive toe-nailing teeth for slip-resistant toe nailing Applications: " Framing, sheathing applications including engineered lumber Tool Description: " Tool Weight: 7.7 lbs. " Driving Power: 1050 inch lbs. @ 100 psi " Magazine Capacity: 100 " Uses wire collated stick nail Applications: " Framing, sheathing applications including engineered lumber " Metal joist hanger and connectors Tool Description: " Tool Weight: 8.1 lbs.<br><br> " Driving Power: 1050 inch lbs. @ 100 psi " Magazine Capacity: 60 F21PL, F33PT Round Head Framing System Features: " Two nailers in one: includes two quick-change nosepieces to convert to either framing or metal connector nailer applications " Patented push-button adjustable depth guide sets nails to desired depths " Lightweight magnesium design for job site durability " 1050 inch lbs. of driving power to tackle tough engineered lumber applications " Molded rubber comfort grip designed to last longer MCN150, MCN250 Metal Connector Nailer MCN150 Features: " Compact design fits between 12", on center joists " Low nail lockout prevents dry fires " Exposed nail tip design fires in the hole for faster, more precise nailing " Long magazine option MCN250 Features: " Low nail lockout prevents dry fires " Exposed nail tip design fires in the hole for faster, more precise nailing " Short magazine option Available in: Plain, galvanized, stainless steel Available in: Plain, galvanized, stainless steel REFER TOTHEPT, RH& S SERIES NAILSECTIONS & THE PT& RHMC METALCONNECTOR SECTIONS ON PAGES 48& 49 REFER TO PT-MC SERIES NAIL SECTION ON PAGE 48 REFER TO 28° WIRE STICK NAIL SECTION ON PAGE 49 Available in: Plain, galvanized .113" to .131" diameter 28° Wire Collated Stick Nails 113"-.162" diameter 21° Plastic Collated Stick Nails 35° Paper Collated Metal Connector Nail Applications: " Framing, sheathing Tool Description: " Tool Weight: 8.4 lbs.<br><br> " Driving Power: 880 inch lbs. @ 100 psi " Magazine Capacity: 225 to 300 depending on nail size N80CB Coil Framing Nailer Features: " Durable aluminum housing " Quick-open composite canister survives falls " Adjustable exhaust directs air away from user Available in: Plain, galvanized, stainless steel REFER TO AC, C, FC NAIL SECTIONS ON PAGES 46 -48 15° Coil Nails 33° Paper Tape Collated Stick Nails MCN (Metal Connector Nails) Hardened .131", .162" Shank Diameter 1-1/2, 2-1/2 Length 11/2" 21/2" 22 Work Safely with Tools, Wear Safety Glasses. For more information on contact, sequential, trigger operated or auto fire see sa fety information on page 5.<br><br> MCN150 Shank Diameters .131 d - .148 d MCN150 MCN250 Shank Diameters .131 d - .162 d Applications: " Fastening Metal Connectors & Strapping Tool Description: MCN150 " Tool Weight: 4.6 lbs. " Driving Power: 450 inch lbs. @ 100 psi " Magazine Capacity: 29 MCN250 " Tool Weight: 6.0 lbs.<br><br> " Driving Power: 600 inch lbs. @ 100 psi " Magazine Capacity: 53 11/2" Tool Description: 650S4 " Tool Weight: 4.7 lbs. "DrivingPwr: 340inchlbs.<br><br> @100psi " Magazine Capacity: 160 " Long Magazine: 300 " 1 to 2 inch leg " Vinyl siding trip for 650S4 - part# 108551 650S5 " Tool Weight: 4.7 lbs. "DrivingPwr: 340inchlbs. @100psi " Magazine Capacity: 160 " Long Magazine: 300 " 1 to 2 inch leg Sheathing, Siding Stapler Features: "AntiJam TM magazine "Overmoldedrubbergripmaximizescomfort "Adjustabledepthguidesetsstaplesto desireddepth "Longnarrow noseforimproved lineofsight Applications: " Sheathing applications requiring up to 2 inch staple legs " 650S414KIT available to drive 14GA high carbon staples through strapping Available in: Coated REFER TO 16 S4, S5 SERIES ON PAGE 50 16-Gauge S4 Staple 16-Gauge S5 Staple 863S4 Flooring Stapler Features: " AntiJam TM magazine permits staples to exit nose without jamming " Narrow nose for improved line of sight " Adjustable trip for staple depth control Applications: " Flooring (plywood to frame) " Sub-flooring Tool Description: " Tool Weight: 5.7 lbs.<br><br> "DrivingPwr: 570inchlbs. @100psi " Magazine Capacity: 160 " Long Magazine: 260 " 1-1/2" to 2 inch leg Applications: " Sheathing (1 1/2 inch leg) " Truss Assembly Tool Description: " Tool Weight: 4.7 lbs. "DrivingPwr: 260inchlbs.<br><br> @100psi " Magazine Capacity: 160 Two-In-One Truss Tool " Stitches truss joints " Attaches truss plates prior to roller press 538S4, 538S214-1 650S4, 650S5 Stapler, Truss Stapler Features: " AntiJam TM magazine permits staples to exit nose without jamming " Long narrow nose for improved line ofsight " Austable trip for positive staple depth control MANUFACTURED HOUSING REFER TO 15 S4 & 15 1/2 S4 GAUGE SECTION ON PAGE 50 Applications: " Pallets assembly and repair " Fence panel assembly " Crate assembly Tool Description: " Tool Weight: 5.7 lbs. " Driving Power: 445 inch lbs. @ 100 psi " Magazine Capacity: 300 to 350 depending on nail size " 1 to 2-1/4 inch (2d to 7d) N58C-1 Box Frame Nailer Features: " Uses wire collated nails " Durable cast aluminum frame and cap " Oversized canister opens completely for fast loading REFER TO AC, C, FC NAIL SECTION ON PAGES 46 - 48 REFER TO 14, 16 S4 STAPLE SECTION ON PAGE 50 15-1/2-Gauge Staple Applications: " Roof to ceiling connections " Timber frames/log homes/ pole barns Tool Description: " Tool Weight: 15.4 lbs.<br><br> "DrivingPwr: 2075inchlbs.@100psi " Magazine Capacity: 50 BIGBERTA160-2 Stick Timber Nailer Features: " Power-packed engine design drives nails up to 6-1/4 inches " Oil-free, requires no lubrication " Includes auxiliary handle for added comfort and control REFER TO 21° PLASTIC COLLATED SECTION ON PAGE 48 & 49 21° Plastic Collated Nails Available in: Plain, galvanized, stainless steel 14-Gauge High Carbon Staple REFER TO THE TOOL & ACCESSORY PART NUMBER GUIDE ON PAGES 56 & 57. 15-Gauge Staple 16-Gauge S4 Staple Available in: Plain, galvanized, stainless steel, aluminum 23 Work Safely with Tools, Wear Safety Glasses. For more information on contact, sequential, trigger operated or auto fire see saf ety information on page 5.<br><br> MANUFACTURED HOUSING 450S2, 438S2R Roofing Stapler Features: " Lightweight durable aluminum frame " Anti-Jam " magazine " Power control valve, adjusts power by 30% " Molded rubber comfort grip designed to minimize fatigue " Reduced height for stapling in tight areas " Rear exhaust directs exhaust away from user " High-capacity, top load magazine decreases reload time " Carbide inserts for long life (438S2R) " 438S2R has adjustable shingle gauge for fast layout Applications: 450S2 " Shingles; roofing felt, housewrap, vapor barrier, butt joints, hurricane strapping 438S2R " Composite shingle roofing " Housewrap, vapor barrier " Sheathing Tool Description: 450S2 " Tool Weight: 4.6 lbs. " Driving Power: 230 inch lbs. @ 100 psi " Magazine Capacity: 160 " 1/2 to 1-1/2 inch leg 438S2R " Tool Weight: 4.7 lbs.<br><br> " Driving Power: 230 inch lbs. @ 100 psi " Magazine Capacity: 160 " 1/2 to 2 inch leg N66BC-1 BOSTITCH ® Cap Nailer Kit Features: "Useswireweldandplasticinsertedcoil nails " Adjustable depth guide " Lightweight magnesium design " Quick-load magazine " Kit includes: tool, carry case * Uses same c series nails as N66C 16-Gauge Staple REFER TO 17 S5 STAPLE SECTION ON PAGE 50 REFER TO STCR5019 SERIES ON PAGE 51 Applications: " Sheathing applications requiring up to 2 inch staple legs Tool Description: " Tool Weight: 5.3 lbs. " Driving Power: 465 inch lbs.<br><br> @ 100 psi " Magazine Capacity: 160 Long Magazine: 300 " 1 1/2 to 2 inch leg 750S5 Sheathing Stapler Features: " AntiJam TM breathing magazine permits staples to exit nose without jamming " Comfort molded grip " Long narrow nose for improved line ofsight " Adjustable trip for positive depth control Applications: " Roofing felt, housewrap vapor barrier application Tool Description: " Tool Weight: 2.1 lbs. " Driving Power: 138 inch lbs. @ 100 psi " Magazine Capacity: 84 " 1/4 to 9/16 inch leg US056-1 Pneumatic PowerCrown TM Stapler Features: " Pneumatic operation for high production felt, insulation and other light-wire stapling applications " Lightweight magnesium design " Oil-free operation requires no regular maintenance and eliminates risk of oil stains " Ultra-quiet rear exhaust " Molded rubber comfort grip designed to minimize fatigue 16/17-Gauge Staple Bostitch ® PowerCrown " Staples STCR5019Series 7/16 d Applications: " Securely fastens most construction fabrics and foam insulation to sheathing Tool Description: N66BC-1 " Tool Weight: 6.1 lbs.<br><br> " Driving Power: 500 inch lbs. @ 100 psi REFER TO 16 S2 SECTION ON PAGE 50 REFER TO C SERIES NAIL SECTION ON PAGE 47 For: 438S2R For: 450S2 SB150SLBC-1 BOSTITCH ® Cap Stapler Kit Features: " Uses wider 5/16" staples that help prevent puncture to the cap " Adjustable depth guide " Lightweight aluminum design " Kit includes: tool, carry case, oil, wrench, 1000 Bostitch ® caps and 1000 staples Applications: " Securely fastens most construction fabrics and foam insulation to sheathing Tool Description: SB150SLBC-1 " Tool Weight: 4.7 lbs. " Driving Power: 300 inch lbs.<br><br> @ 100 psi 18-Gauge SL Staple SMOOTH RING SCREW -11/4" -11/2" -13/4" -2" -23/16" -21/2" 24 Work Safely with Tools, Wear Safety Glasses. For more information on contact, sequential, trigger operated or auto fire see sa fety information on page 5. REFER TO SL SERIES ON PAGE 51 BT35B, BT50B, BT125, BT200 Decorative Molding, Fine Trim Nailer Features BT35B, BT50B Extreme Duty: "Extreme-duty,highcycledesign(requiresoil) "Compositeframealuminummagazine "Narrownoseforimprovedlineofsight Features BT125, BT200 Oil-free: "Oil-freeengine "Magnesiumframecompositemagazine "Narrownoseforimprovedlineofsight "Ultra-quiet,rearexhaust "Auto-fireoptions:BTSXAF-125-KIT andBTSXAF-200-KIT Applications: " Decorative molding, fine trim work " Drawer; pinning French and other dovetail joints Tool Description: BT35B "Tool Weight: 2.4lbs.<br><br> "DrivingPwr: 145inchlbs. @100psi BT125 "Tool Weight: 1.9lbs. "DrivingPwr: 145inchlbs.<br><br> @100psi BT50B "Tool Weight: 2.6lbs. "DrivingPwr: 165inchlbs. @100psi BT200 "Tool Weight: 2.1lbs.<br><br> "DrivingPwr: 170inchlbs. @100psi REFER TO SX SERIES ON PAGE 51 REFER TO FN SERIES ON PAGE 48 N62FN, N52FN MANUFACTURED HOUSING Available in: Coated Available in: Coated Available in: Coated, stainless steel, aluminum Applications: " Roofing/exterior drywall Tool Description: "Tool Weight: 4.8lbs. "DrivingPwr: 410inchlbs.<br><br> @100psi Accessories: Vinyl siding attachment VSA4 RN46 Roofing Nailer Features: " Lightweight magnesium housing for job site durability " Aggressive wear guards and skid pads " Carbide-inserts for long life " Zero nail lockout eliminates dry firing " Patented single action side load canister " 410 in-lbs. of driving energy for the hardest of applications " Quick-set adjustable depth guide sets nails to desired depths " Overmolded grip for comfortable use " Adjustable shingle guide for quick shingle spacing " Full round driver for more consistent drive quality Available in: Galvanized, Stainless Steel Applications: " Cabinet work " Underlayment: (1/4" luan under vinyl flooring) Tool Description: S32SX "Tool Weight: 2.5lbs. "DrivingPwr: 160inchlbs.<br><br> @100psi SX150 "Tool Weight: 2.5lbs. "DrivingPwr: 170inchlbs. @100psi S32SL "Tool Weight: 2.5lbs.<br><br> "DrivingPwr: 160inchlbs. @100psi SL150 "Tool Weight: 2.5lbs. "DrivingPwr: 170inchlbs.<br><br> @100psi S32SX, S32SL, SX150, SL150 Cabinet, Underlayment Stapler Features S32SX, S32SL Extreme Duty: "Extreme-duty,highcycledesign(requiresoil) "Compositeframe/aluminummagazine "Narrownoseforaccuratefastenerplacement Features SX150, SL150 Oil-free: "Oil-freeengine "Magnesiumframecompositemagazine "Narrownoseforimprovedlineofsight "Ultra-quiet,rearexhaust " Auto-fireoptions:BTSXAF-125-KIT andBTSXAF-200-KIT "Longmagazineversions(2xcapacity) SX150LM,SL150LM 18-Gauge SX/SL Staple REFER TO BT SERIES ON PAGE 47 REFER TO COLLATED ROOFING NAIL SECTION ON PAGE 47 REFER TO THE TOOL & ACCESSORY PART NUMBER GUIDE ON PAGES 56 & 57. 15° Coil Nail VSA4 18-Gauge Brad 13/8 d 25 Work Safely with Tools, Wear Safety Glasses. For more information on contact, sequential, trigger operated or auto fire see saf ety information on page 5.<br><br> Applications: " Trim work, drawers, cabinets Tool Description: " Tool Weight: 3.8 lbs. " Driving Power: 400 inch lbs. @ 100 psi " Magazine Capacity: 130 " 1 to 2-1/2 inch 15-ga.<br><br> Finish nail Trim Work, Drawers, Cabinet Nailer Features: " Oil-free engine requires no lubrication " Tool-free removable magazine Also see page 32, FN16250 16-gauge finish nailer. 15-Gauge Finish Nail 16-Gauge Finish Nail BEDDING There 9s no sleeping allowed on this job. Hard-working employees need tools that perform all-day and night.<br><br> Box Frame Assembly: N58C-1 438S4 438S5 BCAR1B-495-92L BCAR-2S Fabric to Wood: 21671B 21671B-LM 21680B Flange to Spring: SC7 SC7C TR201 TR203 TR315 Borderwire to Innerspring: HR-48CCP HR-49CCP VRC Machine HR-85-Series Coil Clip System Fabric to Foam: SL125OC-2 438S4 Stapler connecting flat members SL125OC-2 Flange stapler applying flange to foam side TR203 D-Ring tool connecting flange to innerspring SC7 With manifold kit SCK014 securingpocketedcoilsw/C-Ring Coil clip system and vertical rotating clip machine securing innersprings to borderwire BCAR-2S Stapling foundation spring to flat There 9s a quality Bostitch ® fastener for every application. Check out our Fastener - Tool Selection Guide on pages 46-51 in the back of the catalog. 26 Work Safely with Tools, Wear Safety Glasses.<br><br> For more information on contact, sequential, trigger operated or auto fire see sa fety information on page 5. BEDDING N58C-1 Box Frame Nailer Features: " Uses wire collated nails " Durable cast aluminum frame and cap " Oversized canister opens completely for fast loading Applications: " Box frame/flat assembly Tool Description: " Tool Weight: 4.6 lbs. " Driving Power: 230 inch lbs.<br><br> @ 100 psi " Magazine Capacity: 160 " 1/2 to 1-1/2 inch leg 438S4, 438S5 Box Frame Stapler Features: " Lightweight durable aluminum frame " Jam-free magazine " Power control valve, adjusts power by 30% " Long-lasting molded rubber comfort grip " Reduced height for stapling in tight areas " Rear exhaust directs exhaust away from user and work surface " High-capacity, top load magazine decreases reload time Applications: " Spring up (attaching springs to box frame) Tool Description: " Tool Weight: 7.4 lbs. " Magazine Capacity: 100 " Staple Length: 3/4 inch BCAR1B-495-92L, BCAR-2S Attaching Spring to Box Frame Features: " Pneumatic stapler for driving staples into hard-to-reach places such as bottoms of coil springs " Available in single or double staple fire versions Applications: " Pocket coil to pocket coil " Pocket coil to borderwire " Flange to innerspring/borderwire Tool Description: " Tool Weight: 2.8 lbs. " Magazine Capacity: 125 " Jaw Length: 1-1/4 inch SC7, SC7C Spring to Spring Features: " Balanced, lightweight, ergonomically designed " Easy-to-load anti-back-up magazine " Can be easily converted to right or left hand operation " Manifold mounting kit available for zero gravity balancer suspension (vertical or horizontal): SCK014 " Zero gravity balancer: BAL5N (Shown with balancer and manifold kit options) REFER TO AC, FC SERIES ON PAGE 46 - 48 REFER TO 16 S4 STAPLE SECTION ON PAGE 50 REFER TO ROUND CROWN BOX SPRING SECTION ON PAGE 51 REFER TO #3 ON PAGES 54 & 55 Available in: Coated Available in: Basic brite steel, galvanized, aluminum, stainless RING15100P Closure w/ SC7C Closure w/ SC7 BSC31, BCS31P 16-Gauge Round Crown Staple 16- Gauge S4 Staple REFER TO THE TOOL & ACCESSORY PART NUMBER GUIDE ON PAGES 56 & 57.<br><br> 16- Gauge S5 Staple BSC31 Collated with adjacent chisel points in same direction. BCS31P Collated with adjacent chisel points in opposite directions. Applications: " Pallets assembly and repair " Fence panel assembly " Crate assembly Tool Description: " Tool Weight: 5.7 lbs.<br><br> " Driving Power: 445 inch lbs. @ 100 psi " Magazine Capacity: 300 to 350 depending on nail size " 1 to 2-1/4 inch (2d to 7d) 27 Work Safely with Tools, Wear Safety Glasses. For more information on contact, sequential, trigger operated or auto fire see saf ety information on page 5.<br><br> Applications: " Securing fabric to wood frame " Pre-upholstery spring up operation: attach cardboard, webbing, propex to frame " Boat Seating with stainless steel staples " 21697B Attaching double welt Tool Description: 21671B " Tool Weight: 1.81 lbs. " Magazine Capacity: 196, 71 series staples 21671B-LM " Tool Weight: 2.43 lbs. " Magazine Capacity: 392, 71 series staples 21680B; 21680B-LN " Tool Weight: 1.83 lbs.<br><br> " Magazine Capacity: 156, 80 series staples Fabric to Wood Assembly Features: 21671B: " Very lightweight, rugged, all metal construction, quiet, low air consumption 21671B-LM: " Same as BAT401 but with long magazine; cuts reloading time 21680B, 21680B-LN (long nose): " Same as 21671B but fires 80 series staples BEDDING Applications: " Flange to inner spring Tool Description: " 15 ga. 3/4 D rings, 1/4 inch min. closure " Short Magazine: 55 rings, 3.3 lbs.<br><br> " Long Magazine: 125 rings, 3.6 lbs. TR201, TR203, TR315 Flange to Innersprings Features: " TR201 Spring returned tool " TR203 Spring returned tool long mag. " TR315 High-speed air return, long mag.<br><br> " Magazine can be pivoted in 90Ú increments on TR315, and continuously on TR201 and TR203 HR-85C-110 Borderwire to Wire Features: " Clinching tool squeezes instead of folding the clip around wires " Driver blade cleanly feeds a clip from the magazine, places it around the wires, and forms the clip into a tight strong wire bond. Applications: " Foundation/box spring assembly " Border wire overlap connections " Clip-on edge supports " Rebuilding and custom sizes Tool Description: " Driving Power: 2000 inch lbs. " Magazine Capacity: 25 to 45 collated clips 21671B, 21671B-LM, 21680B, 21680B-LN REFER TO #5 ON PAGES 54 & 55 REFER TO CLIPS/CLIP TOOLS ON PAGES 52 & 53 AND CLIP SELECTION GUIDE ON PAGE 45 REFER TO 71, 80 SERIES STAPLE SECTION ON PAGE 50 & 51 Available in: Basic Steel, galvanized, stainless 71 Staple 80 Staple 15-Gauge D-Ring Width Crown Diameter (opening) Height Applications: " Fastening flange to foam encased innerspring " Fabric to cardboard, foam " Temporary pinning of fabric Tool Description: " Tool Weight: 2.8 lbs.<br><br> " Driving Power: 160 inch lbs. @ 100 psi " Magazine Capacity: 100 " Staple Length: 1 inch typical (SL5031G) SL125OC-2 Fabric to Foam Stapler Features: " Designed for staple legs to flare outward, giving good holding power in soft material " Adjustable flare from straight staple to moderate flare for good holding in thick, soft material to severe flare for shallow materials where staple cannot show on other side. SL Series: 5/16'' Crown 28 Work Safely with Tools, Wear Safety Glasses.<br><br> For more information on contact, sequential, trigger operated or auto fire see sa fety information on page 5. REFER TO SL SERIES ON PAGE 51 -HR-55450 tool stand assembly -HR-55435 dispenser and track assembly -132979 tool balancer -HR-65002 3/8" hose assembly -HR-65006 king size (86" x 72") rotating table -HR-65007 full size (58" x 72") rotating table Tools: HR-48CCP HR-49CCP COIL CLIP SYSTEM Borderwire Assembly Features: " Provides a simple and efficient means of attaching borderwire to innerspring units " System allows operators to apply clips from a continuous clip coil at an average rate of 20,000 clips/8-hour shift Applications: " Borderwire sides to innersprings Machine Description: " Tool Weight: 2000 lbs. (2500 lbs.<br><br> crated) " Magazine Capacity: 9375 to 15,625 clips per clipping head VRC MACHINE Borderwire to Innersprings Features: " Used in conjunction with the coil clip system for clipping borderwire to sides of innerspring assemblies " Clipping speed for Bonnel/Offset Bonnel and LFK coil assemblies is faster than previous VRC models. A single machine will now easily keep up with an experienced operator on the coil clip system. " The process of clipping an innerspring is as follows: An innerspring is taken off the transfer/coiler by an operator and placed on the rotating work table.<br><br> The operator retrieves two borderwires and positions them on the innerspring. They are attached to the perimeter corner coils using the Clip Tool. The unit is now pre-clipped and is taken off the table and placed on the VRC Machine.<br><br> The operator presses the start button and the machine runs automatically to finish attaching the borderwires. While the machine clips the borderwires, the operator pre-clips another unit. The NEW faster VRC will finish clipping at the same time the operator finishes the second pre-clipping operation.<br><br> The next pre-clipped unit is placed on the right side of the machine, the machine is started, and the first finished unit is unloaded. " CE compliant option available " Programmable in English and Spanish REFER TO COIL CLIP 7/16" ON PAGE 52 AND CLIP SELECTION GUIDE ON PAGE 45 REFER TO COIL CLINCH CLIP 7/16" WIDE SECTION ON PAGE 52, AND CLIP SELECTION GUIDE ON PAGE 45 Width Crown Diameter (opening) Height Width Crown Diameter (opening) Height Applications: " Pre-clipping operation: Attaching corners of borderwire to corners of innerspring assembly prior to full clipping by VRC Machine " Can also be used to clip entire borderwire to innerspring assembly in low-volume operations Tool Description: System consists of: 29 Work Safely with Tools, Wear Safety Glasses. For more information on contact, sequential, trigger operated or auto fire see saf ety information on page 5.<br><br> BEDDING REFER TO THE TOOL & ACCESSORY PART NUMBER GUIDE ON PAGES 56 & 57. MILLWORK From decorative molding-fine trim work and even case backs, Bostitch has the industrial-strength pneumatic tool for the job. Structural Assembly: 450S2 450S2 538S4 N58C-1 N62FN N52FN TU-225-18HP HP118K SX150 SL150 FN16250 Trim Work: S32SX S32SL BT35 BT50 BT125 BT200 Door/Window Frames: 650S4 650S5 CF15 MCF16 There 9s a quality Bostitch ® fastener for every application.<br><br> Check out our Fastener - Tool Selection Guide on pages 46-51. 30 Work Safely with Tools, Wear Safety Glasses. For more information on contact, sequential, trigger operated or auto fire see sa fety information on page 5.<br><br> Fast, accurate and built to work... and work... and work.<br><br> CF15 Corrugated tool applying mitre fastener to window frame 450S2 Stapler joining door jambs Custom Millwork Calls for Premium Quality Tools and Fasteners. Applying 18-gauge brad to door casing 16-gauge finish nails connecting brick molding to a window frame 31 Work Safely with Tools, Wear Safety Glasses. For more information on contact, sequential, trigger operated or auto fire see saf ety information on page 5.<br><br> MILLWORK N62FN, N52FN Finish Nailers Features: " Sequential trip " Oil-free engine requires no lubrication " Tool-free removable magazine Applications: " Fine trim work Tool Description: TU-225-18HP (18 GAUGE) " Tool Weight: 2.3 lbs " Magazine Capacity: 230 HP118K (23 GAUGE) " Tool Weight: 2.3 lbs " Magazine Capacity: 230 TU-225-18HP, HP118K 18 & 23-Gauge Headless Pinner Features: " Adjustable high/low power control " Lightweight, durable aluminum housing " Overmolded grip " Rear exhaust Available in: Coated, stainless steel, aluminum REFER TO 18-GA & 23-GA HEADLESS PIN SECTION ON PAGE 49 REFER TO FN15 SERIES ON PAGE 48 15-Gauge Finish Nail 16-Gauge Finish Nail For N52FN: For N62FN: REFER TO SX SERIES ON PAGE 51 Available in: Coated Applications: " Cabinet work " Underlayment: (1/4 luan under vinyl flooring) Tool Description: " Tool Weight: 2.5 lbs. " Driving Pwr: 170 inch lbs. @ 100 psi " Magazine Capacity: 100 " Long Magazine: 200 " 1/2 to 1-1/2 inch leg S32SX, S32SL Cabinet, Underlayment Stapler Features S32SX, S32SL: Extreme Duty: "Extreme-duty,highcycledesign(requiresoil) "Compositeframe/aluminummagazine "Narrownoseforimprovedlineofsight Features SX150, SL150: Oil Free: "Oil-freeengine "Magnesiumframecompositemagazine "Narrownoseforimprovedlineofsight "Ultra-quiet,rearexhaust "Auto-fireoptions:BTSXAF-125-KIT andBTSXAF-200-KIT "Longmagazineversions(2xcapacity) SX150LM,SL150LM 18-Gauge SX Staple BT35B, BT50B, BT125, BT200 18-Gauge Brad 18-Gauge Brad 13/8 d FN16250 Features: " Lightweight magnesium design for added durability " Oil-free operation requires no regular maintenance and eliminates the risk of oil stains " Adjustable depth guide sets nails to desire depths quickly and conveniently " Tool-free removable magazine for fast cleaning and jam-clearing Applications: " Interior finish/trim " Door jams Tool Description: " Tool Weight: 3.8lbs.<br><br> "DrivingPwr: 400inchlbs.@100psi. " Magazine Capacity: 130 " 1 to 2-1/2 inch 16-ga. Finish nail 32 Work Safely with Tools, Wear Safety Glasses.<br><br> For more information on contact, sequential, trigger operated or auto fire see sa fety information on page 5. REFER TO FN15 SERIES ON PAGE 48 Extreme Duty Decorative Molding, Fine Trim Nailer Features BT35B, BT50B Extreme Duty: "Extreme-duty,highcycledesign(requiresoil) "Compositeframealuminummagazine "Narrownoseforimprovedlineofsight Features BT125, BT200 Oil-free: "Oil-freeengine "Magnesiumframecompositemagazine "Narrownoseforimprovedlineofsight "Ultra-quiet,rearexhaust "Auto-fireoptions:BTSXAF-125-KIT andBTSXAF-200-KIT Applications: " Decorative molding, fine trim work " Drawer; pinning French and other dovetail joints Tool Description: BT35B " Tool Weight: 2.4 lbs. " Driving Pwr: 145 inch lbs.<br><br> @ 100 psi BT125 " Tool Weight: 1.9 lbs. " Driving Pwr: 145 inch lbs. @ 100 psi BT50B " Tool Weight: 2.6 lbs.<br><br> " Driving Pwr: 165 inch lbs. @ 100 psi BT200 " Tool Weight: 2.1 lbs. " Driving Pwr: 170 inch lbs.<br><br> @ 100 psi Applications: " Structural assembly, casings, etc. " Medium duty finish nail structural assembly Tool Description: N62FN / N52FN " Tool Weight: 3.7 lbs. / Same "DrivingPwr: 330inchlbs.<br><br> @100psi/Same " Magazine Capacity: 130 / Same " 1 to 2-1/2 inch 15-ga. Finish nail / 1 to 2 inch 16-ga. Finish nail 16-Gauge Finish Nail 23-Gauge Headless Pin 18-Gauge Headless Pin REFER TO FN15 SERIES ON PAGE 48 MILLWORK Applications: " Medium duty structural assembly Tool Description: " Tool Weight: 4.7 lbs.<br><br> "DrivingPwr: 280inchlbs. @100psi " Magazine Capacity: 160 " 3/8" to 1-1/2 inch leg 538S4 Medium DutyStructuralStapler Features: " Anti-Jam TM magazine permits staples to exit nose without jamming " Narrow nose for improved line of sight " Adjustable trip for positive staple depth control Applications: " S4: door and window frames " S5: door and window frames Tool Description: " Tool Weight: 4.5 lbs. "DrivingPwr: 340inchlbs.<br><br> @100psi " Magazine Capacity: S4: 160, S5: 171 " 1" to 2 inch leg 650S4, 650S5 Door, Window Frame Stapler Features: " Powerful engine for driving into hardwood " Narrow nose for improved line of sight Applications: " Structural assembly Tool Description: " Tool Weight: 5.6 lbs. " Driving Power: 475 @ 100 psi " Magazine Capacity: 300 to 350 N58C-1 Structural Assembly Nailer Features: " Lightweight, compact design CF15, MCF16 Door, Cabinet Mitre Nailer Features: " Lightweight Applications: " Joining door stiles, cabinet face frames " Stile assembly, door window fabrication Tool Description: CF15-2 " Tool Weight: 6.58 lbs. " Magazine Capacity: 128 MCF16 " Tool Weight: 4.75 lbs.<br><br> " Magazine Capacity: 156 Available in: Coated Available in: Coated REFER TO 16 S4 SERIES ON PAGE 50 REFER TO 16 S4, S5 SERIES ON PAGE 50 REFER TO A, AC, FC SERIES ON PAGES 46 THROUGH 48 REFER TO CORRUGATED/MITRE FASTENER SECTION ON PAGE 49 16-Gauge S4 Staple 16-Gauge S4 Staple 16-Gauge S5 Staple REFER TO THE TOOL & ACCESSORY PART NUMBER GUIDE ON PAGES 56 & 57. Applications: " Light duty structural assembly Tool Description: " Tool Weight: 4.6 lbs. "DrivingPower: 230inchlbs.@100psi " Magazine Capacity: 160 " 1/2 to 2 inch leg 450S2 Light Duty Structural Assembly Stapler Features: "Lightweightdurablealuminum frame "Jam-freemagazine "Powercontrol valve, adjustspowerby30% "Long-lastingmoldedrubbercomfortgrip "Reducedheightforstaplingintightareas "Highcapacity, toploadmagazine decreasesreloadtime 16-Gauge S2 Staple Available in: Coated REFER TO 16 S4, S5 SERIES ON PAGE 50 33 Work Safely with Tools, Wear Safety Glasses.<br><br> For more information on contact, sequential, trigger operated or auto fire see saf ety information on page 5. Corrugated Mini Corrugated For CF15: For MCF16: PACKAGING (CARTON AND BAG CLOSURE) CARTON CLOSURE Companies thrive on getting the job in and then out. Bostitch has an extensive line of carton closure tools and fasteners to help get the boxes out the door.<br><br> P3-IND P6C-6 P6C-8 P6C-8P JB600 ESD-450S2P P50-10B P50-5B PC3000 PC4000 F84 FC95EC D16-2 D16-2AD D61ADC D61ADCSB FC95EC Bottom closer used to clinch carton bottoms P50-10B Fastening carton side P6C-8P With pointed anvil piercing corrugated to seal container from outside D61ADC Sealing carton lid There 9s a quality Bostitch ® fastener for every application. Check out our Fastener - Tool Selection Guide on pages 46-51. 450S2 ESD-450S2-WS 02245 34 Work Safely with Tools, Wear Safety Glasses.<br><br> For more information on contact, sequential, trigger operated or auto fire see sa fety information on page 5. BAG CLOSURE From poultry to automotive parts, if it comes packaged in a bag, we have the closure to make sure it stays there. P6C-8F P7 HFP9 SC7 SC760 SC50T SC761 SC743 SC7C Low cost P7 being used to seal potato bag Bait bag secured with 15-gauge stainless steel C-ring Oil absorption socks can be secured with 11, 15 or 16-gauge blunt C-rings 35 Work Safely with Tools, Wear Safety Glasses.<br><br> For more information on contact, sequential, trigger operated or auto fire see saf ety information on page 5. SC7 Equipped with MTCKA7 touch trip PACKAGING (CARTON CLOSURE) 7/16 d Bostitch ® PowerCrown " Staples STCR5019 Series Bostitch ® Light Wire PowerCrown " Staples STCR2619 Series REFER TO 3/8'' CROWN STAPLE SECTION ON PAGE 51 REFER TO STCR2619 AND STCR5019 SECTIONS ON PAGE 51 REFER TO STCR2619 AND STCR5019 SECTIONS ON PAGE 51 P3-IND Tagging, Wrapping, Shipping Features: " Fine wire lightweight staple " Top load magazine with cover/pusher that stays with the tool " Rugged design for heavy use with moveable, breathing core to prevent jamming " Pass-by clinch so one staple will fasten various thickeness applications Applications: " Dry cleaner garment tagging, drugstore bag closure, price tag to garment, etc. " Flower wrapping " Badges and ribbons " Shipping room packaging Tool Description: " Tool Weight: 0.5 lbs.<br><br> " Magazine Capacity: 208 Tool Description: P6C-6 " Tool Weight: 1 lbs. " Magazine Capacity: 158 " Throat Size: ~3/8" x 2-1/2" P6C-8 " Tool Weight: 1 lbs. " Magazine Capacity: 85 " Throat Size: ~3/8" x 2-1/2" " Pneumatic assembly available JB600 " Tool Weight: 2.4 lbs.<br><br> " Magazine Capacity: 85 " Throat Size: ~3/8" x 2-1/2" Applications: P6C-8: " Header cards to plastic bags " Box closing " Corrugated assembly " Dry cleaning JB600: " Lightweight manufacturing and packaging P6C-6, P6C-8, P6C-8P, JB600 Box Closing, Dry Cleaning Features: P6C-8: " Bearing system allows an easy squeeze action across entire operating sequence creating a quicker, tighter clinch with less strain " Available in P-Poi

less