Importing Fonts from Corel Draw ® 1 GUNNAR SPT32 Importing Fonts from Corel DRAW ® by Jared Davis CPF, GCF Importing Fonts from Corel Draw ® 2 Weissenberger AG Staatsstrasse 119 CH 3 9445 Rebstein Tel: +41 (071) 775 8220 Fax: +41 (071) 775 8229 Internet: www.gunnar-europe.com GUNNAR is a registered trademark of Weissenberger AG, Switzerland Corel DRAW ® is a registered trademark of Corel Corporation, USA Importing Fonts from Corel Draw ® 3 Index Introduction 4 Step 1 3 Typing Your Word 5 Opening Corel DRAW 5 Typing your word with the Text Tool 5 Step 2 3 Converting from Text to Shapes 7 Why do we need to convert the text into a shape? 7 Convert to Curves 7 Break Apart 7 Changing the view 8 Super-Size it! 3 Make it bigger 8 Copy & Paste 8 Step 3 3 Pasting into SPT32 9 Opening Gunnar SPT32 9 Pasting into Gunnar SPT32 9 Paste dialogue settings 9 Step 4 3 Cutting Tips 11 Test cutting 11 Smoothing things out 11 Cutting internal fallouts 12 Saving the file 12 Frequently Asked Questions 13 Importing Fonts from Corel Draw ® 4 Even though Gunnar SPT32 has its own cFont Mode ... more. less.
d, it has its limitations when it comes to cutting small and difficult fonts.<br><br> Much better results can be achieved by importing fonts from Corel DRAW ® . This tutorial guide was specifically created to help explain the methods and techniques of importing text and fonts from Corel DRAW ® into Gunnar SPT32, in a cstep by step d format, to allow you to achieve desirable and impressive results when cutting more detailed & difficult fonts. Corel Draw X4 (14), and Gunnar SPT32 V6.2 were used as reference for this document, when it was written.<br><br> This guide has been written in a style that assumes that the reader already has a basic knowledge and understanding of the Gunnar SPT32 software, and an existing level of confidence and experience with PC 9s. Patience & practice are the keys to achieving success, so don 9t be disappointed if you cannot achieve what you want in the first circumstance. Try to attempt simple tasks first, before diving into any advanced, elaborate designs.<br><br> Good luck, and happy matcutting! www.jared-davis.com Jared Davis CPF,GCF Introduction Importing Fonts from Corel Draw ® 5 Opening Corel DRAW You can open Corel DRAW from the Windows desktop by following these directions: Start All Programs Corel DRAW Corel Draw . Create a NEW document on a blank screen .<br><br> It 9s OK to have SPT32 running at the same time, in the background . Typing your word with the Text Tool On the Menu Bar at the left hand side of the screen, select the c Text Tool d, or use the keyboard shortcut c F8 d. On the Menu Bar at the top of the screen, select your desired font from the drop down menu.<br><br> When the cText Attributes d window comes up on the screen, just click on c OK d. Step 1 3 Typing Your Word Importing Fonts from Corel Draw ® 6 Head back to the Menu Bar at the top of the screen again, and type in the font size value to be c 400 d. When the cText Attributes d window comes up on the screen (again!), just click on c OK d.<br><br> With the mouse, position the pointer on the screen where you want the text cursor to be place (with a left click), so you can start typing your word. Type in your word! Importing Fonts from Corel Draw ® 7 Why do we need to convert the text into a shape?<br><br> Standard text typed into Corel DRAW needs to be ctraced d into vectors and points, so that the Corel DRAW software (and SPT32) can recognise these as shapes, made up of joined co-ordinates and lines, rather than formal text. Doing this is a simple series of steps as follows: Convert to Curves With the text still selected, go to the Menu Bar at the top of the screen and follow this shortcut: Arrange Convert to Curves . Alternatively you can also use the keyboard shortcut c CTRL Q d.<br><br> Break Apart Now that the text is converted to shapes and curves, we need to ungroup everything so that it is separated into individual shapes for SPT32 to understand, rather than one complete object. Once again, go to the Menu Bar at the top of the screen and follow this shortcut: Arrange Break Artistic Text , or use the keyboard shortcut c CTRL K d. Step 2 3 Converting from Text to Shapes Importing Fonts from Corel Draw ® 8 If you have an older version of Corel DRAW, the option may say c Break Apart d, which is the same thing.<br><br> Changing the view In the Menu Bar at the top of the screen, go to View Wireframe . This removes any fill and colour from the image, which makes it easier to clearly see the vector lines and control points which make up the image. Super-Size it!<br><br> - Make it bigger It 9s always best to make your word bigger before importing it into SPT32. The larger your design is in Corel Draw, the more accurate and smoother the imported design will cut in SPT32. To csuper-size d your shape or design, use the default c pick tool d to select the object, and then select a corner with the mouse and cclick and drag d the image to a larger size.<br><br> The larger you go, the better the result. Aim for about 1000mm (or 40 d) wide. The c pick tool d is the default mouse pointer tool, which can be found on the top of the tool menu on the left hand side of the screen.<br><br> Don 9t worry about making the design too big, because you can always reduce the size of it to a desired level, when you paste it into SPT32 later. Copy & Paste When you have completed these steps, use the mouse to create a lasso around the entire word, to select all the letters as a group, and then type in c CTRL C d to copy final image to c Windows Clipboard d. Importing Fonts from Corel Draw ® 9 Opening Gunnar SPT32 One of the features of Microsoft Windows is that it allows you to cmulti-task d and have more than one program running at the same time.<br><br> We can utilize this feature to allow us to ccopy & paste d a design from one program to another. Make sure SPT32 is now running simultaneously with Corel DRAW, if it is not already. Pasting into Gunnar SPT32 Click on the c Paste from Clipboard d button in SPT32 to paste the shapes you have been working with in Corel DRAW.<br><br> Alternatively, you can just use the common keyboard shortcut for paste 3 c CTRL V d. If nothing happens, then you need to try copying the shapes in Corel DRAW to the cWindows Clipboard d again. Paste dialogue settings Firstly, make sure the c Closed polygons d & c proportional d options are both checked.<br><br> If you have csupersized d the word in Corel DRAW, then by default it will also be pasted into SPT32 csupersized d as well, at a ratio of 1:1. This means that you will need to reduce the size of the image using c paste dimension d x & y values. For example, you may wish to make the height of the lettering 40mm, which means you would make the c paste dimension y d value equal to 40mm.<br><br> Make sure your c paste position d x & y values are at least 50mm each, to keep a safe distance from the clamps. Make sure that the c tangential settings d scale is set for a value of 36 . Once all the settings have been configured in the dialogue box to your requirements, hit the c Enter d key to place your word on the screen.<br><br> Step 3 3 Pasting into Gunnar SPT32 Importing Fonts from Corel Draw ® 10 After a few seconds, the letters will be visibly placed on the view screen, ready for you to position and cut. When pasting, sometimes the outside dimensions of your mat may need to be increased if the words has run off the screen. This can be adjusted in the c sizes d tab, above the templates on the left hand side of the screen.<br><br> Don 9t try to import too many letters or words in one step. If you have more than 1-2 words, then import them into SPT32 as separate steps. Importing Fonts from Corel Draw ® 11 Test cutting ALWAYS perform a test cut of an imported design on a scrap piece of matboard, before cutting into your final cgood d piece of matboard.<br><br> Just because a design looks OK on the screen, doesn 9t always mean that it will cut well. You always need to perform test cuts first. When test cutting an imported font in general, it is a good idea to test cut a few of the charder d letters like c S d and c Q d to see how these work first.<br><br> If you can easily cut the charder d letters, then you can be more confident that the simple letters should be OK too. Use a new blade and a new slip mat. New blades do not break as easily as used blades.<br><br> Expect that you make break a blade if you are cutting tight curves & circles, which may then require further modification and adjustment to the file in Corel DRAW. Cut from the back! Small letters will cut better from the back of the matboard, than they will from the front, because cutting from the back helps keep the fallouts in place and stop them from moving while cutting.<br><br> You may find that reducing the cutting speed can also give you better results (and less broken blades!). Cutting unrealistic tight curves at high speeds can easily snap blades. With very detailed designs with lots of curves and flexes, you will probably need to change the blade more frequently than usual.<br><br> You can use the c spacebar d pause function to interrupt a cut and change the blade part way through. Sometimes further modifications and adjustments may be required in order to achieve perfect results. For example - sometimes if letters are placed too close together, then the matboard may fall apart.<br><br> Smoothing things out& For smoother and better quality cuts, you may need to go back to Corel DRAW and either make the file bigger again, or clean up and smooth out some of the control points and lines. Please refer to the cSolutions for Importing from Corel DRAW d guide for more detailed information on how to do this. Step 4 3 Cutting Tips Importing Fonts from Corel Draw ® 12 If you have any letter c O d 9s in the word that happen to be cperfect d circles or ovals, then you will probably find that you achieve better results by re- create them in SPT32 as an oval, rather than cutting them as an imported shape from Corel DRAW.<br><br> A circle generated by SPT32 will always cut better than one imported from Corel DRAW. Cutting internal fallouts Some people apply a reverse bevel ( RB ) to these internal openings, so that they cut with the bevel the preferred way. Some people prefer to cut these internal openings in a separate process later, on a scrap piece of matboard inserted cface up d in the machine (even though the software is still in ccut from back d.<br><br> This method may also require an extra step of c Mirror Horizontal d applied, if the internal openings are not symmetrical. This function can be found in the ctransform menu d, in the Menu Bar at the top of the screen. For a better proportional distance and width of the letters, try reducing the size of your fallouts by 20%, using the cScaling d feature, which is also found in the ctransform menu d, in the Menu Bar at the top of the screen.<br><br> Try sticking your internal fallouts to your matboard with a very small dab of PVA glue, rather than trying to apply double sided tape to very small, fiddly bits of matboard. Saving the file Once a design has been tested and proven to cut fine, you can save it for later, know that it will confidentially cut well again, without having to test it again. Saving the file in SPT32 should be straightforward, however don 9t forget to add some notes to the file, if you performed any extra adjustments or modifications that you will need to remember next time.<br><br> It is also advisable to save your original Corel DRAW c *.cdr d file as well, in case you need it again for future use. Importing Fonts from Corel Draw ® 13 Why does the blade not cut all the way through the mat on the tight curves? The blades can flex when they cut around a tight corner or curve, thus reducing their effective depth of penetration.<br><br> This can be fixed by manually increasing the blade depth by adjusting the grub screw on the blade holder (half a turn anticlockwise is usually enough) Why do I seem to be getting undercuts in the corners of some of my cut letters? By default, the overcut settings in SPT32 are optimized specifically for right angled corners (ie: rectangles). This means that some acute angles may undercut slightly, and not cut all the way thru.<br><br> This can be adjusted by temporarily increasing your overcut settings, and/or your blade depth. Can I export a file from Gunnar SPT32 back into Corel Draw? No, unfortunately, this feature is not available.<br><br> For this reason it is advisable that you always save your original Corel DRAW c*.cdr d files for future use again, if required. How can I change the size of a previously saved imported words or letters? If it is a group of letters or a word, then the easy way to do this is to use the cScaling d feature in the ctransform menu d, which is on the main tool bar on the top of the screen in SPT32.<br><br> You can adjust the size of the image by applying a scale factor to the dimensions. You can also change the size of an individual shape just by cdouble-clicking d on it, and redefining the dimensions in the paste dialogue box. Always perform a test cut of any imported design whenever you change the size of it, to be sure it will cut out ok.<br><br> Which version of Corel DRAW do you recommend that I use? This depends on the version of SPT32 that you are using. If you are using the most recent version of SPT32 (V6.1), then you will find that it has been optimized for use with Corel DRAW Version X4.<br><br> However you could use an older version as such as Corel DRAW Version 9, but you may find you have some minor issues? Frequently Asked Questions Importing Fonts from Corel Draw ® 14 What does ctangential settings d mean? This value controls where the matcutter chooses to make a chard stop d (ie: retract blade, rotate, insert blade) along a cut on a line.<br><br> If this value is set too low, the machine will recognize more control points, and make more chard stops d, thus creating a more jagged cut along a curve, where it really should be smooth. If the value is set around 36, it will ignore most hard stops along a curve, and keep the cut continual and smooth, but still stop where it is supposed to. If you set the tangential settings value really high, the machine may not recognize obvious ccorners d where it should really be stopping and keep cutting, thus possibly snapping a blade.<br><br>