Rain-Garden Design and Implementation for Kansas Property Owners With a Discussion of Lessons Learned from Kansas State University 9s International Student Center Rain-Garden Design-Build Demonstration Project in Manhattan, Kansas Introduction What a rain-garden looks like and how it functions Why rain-gardens are needed and valued Other stormwater management options Steps to Create a Successful Rain-Garden 1. Understanding Your Property and Its Context 2. Locating and Sizing a Rain-Garden 3.
Preparing a Place-Specific Rain-Garden Planting Design 4. Excavating and Preparing Soil for the Rain-Garden 5. Installing and Watering Plants 6.
Monitoring and Caring for Your Rain-Garden Common Rain-Garden Questions & Answers Appendices (Case Studies, including designs and plant list for the KSU-ISC Rain-Garden) The Kansas Department of Health and Environment (KDHE) provided financial assistance to the KSU- ISC Rain-Garden Project through EPA Section 319 Nonpoint Source Pollution Control Grant #C9007405-12. Three WaterLINK (Water Quality Restoration and Protection Service Learning Mini- Grants awarded to KSU by KDHE utilizing EPA funds) provided financial assistance for the Fall 2006 KSU Campus Creek Planning/Design Charrette, Spring & Summer 2007 KSU-ISC Rain-Garden Construction, and Fall 2007 rain-bowl designs for the KSU-ISC Rain-Garden. A Spring 2008 WaterLINK Grant, also awarded to KSU by KDHE using EPA funds, helped secure ... more. less.
plants and pay for travel associated with the Rossville Rain-Garden project.<br><br> Many KSU faculty, staff, and students assisted with design and implementation efforts. Professor Lee R. Skabelund served as Principal Investigator, Designer, and Projects Coordinator.<br><br> Cary Thomsen was Lead Designer for the KSU-ISC Rain-Garden, with advice on plantings provided by Tor Jansen and Tim Keane, and the level-spreader designed by Dennis Day. Brett Tagtmeyer and Aarthi Padmanabhan were lead designers for the Rossville Rain-Garden. Primary References: Blue Thumb Guide to Raingardens: Design and Installation for Homeowners in the Upper Midwest .<br><br> Authors: Rusty Schmidt, Dan Shaw, David Dods. 2007 Waterdrop Innovations, LLC. Provides a very readable discussion of how to create rain-gardens in different contexts on residential properties and includes a guide for planting in USDA Zones 3, 4, and 5.<br><br> Many excellent ideas are presented in this guide, and have been adapted in the following pages. Rain Garden Handbook for Western Washington Homeowners http://www.pierce.wsu.edu/Water_Quality/LID/Raingarden_handbook.pdf Discusses a four-step process for creating rain-gardens, with excellent supporting graphics. Introduction What a Rain-Garden Looks Like and How It Functions In the Flint Hills Eco-region and other parts of Kansas where prairie is the dominant historic vegetative community, rain-gardens can look and function much like a perennial garden.<br><br> The difference is that rain-gardens are intentionally designed to absorb the first inch or so of stormwater runoff from rooftops, pavement, and other impermeable surfaces of land. If a rain- garden holds more or less than the first inch of precipitation that is fine. What matters is that we try to reduce negative stormwater impacts on our aquatic resources, and rain-gardens can help!<br><br> Using native prairie species makes rain-gardens well adapted to our harsh Kansas climate, but other kinds of plants can also be used. However, please avoid invasive species! Konza Prairie 3 October 25, 2005 photo by Lee Skabelund Why are rain-gardens needed and valued?<br><br> In most urban and suburban areas, and almost everywhere we have built homes, driveways, and streets, untreated stormwater flows directly across rooftops, pavements and lawns, into ditches or inlets and pipes, and is then quickly conveyed to local creeks, streams and rivers. This process, called stormwater runoff , creates dispersed (or non-point-specific) water pollution, and is a leading cause of degraded streams, rivers, lakes, estuaries, and other aquatic ecosystems. In fact, the US-EPA indicates that stormwater runoff is the most significant threat to water quality in lakes and streams 3 as well as to the Gulf of Mexico and other estuaries.<br><br> In recent years, rain-gardens and other cbest management practices d (BMPs for short) have been designed and implemented in an attempt to slow, hold, filter and infiltrate stormwater as near as possible to the places where rain and other forms of precipitation fall to the earth. Rain-gardens are a solution that can be readily adapted to capture and infiltrate stormwater on nearly every property, no matter the type of soils or slopes. Rain-Garden sketch by Tim Merklein (KSU-LA/RCP 2008) Residential Stormwater Retrofitting: An Educational Guidebook for Pottawatomie County, Kansas Timothy Merklein, Dept.<br><br> of Landscape Architecture / Kansas State University - Capstone 2008 (pg 32). Why is effective stormwater management important? If stormwater is allowed to move too far and too rapidly this flowing water will accumulate and create larger more concentrated flows, typically causing soil erosion in our upland landscapes, as well as excessive streambank erosion and sedimentation along our creeks, streams, and rivers.<br><br> How do we stop stormwater from concentrating? There are many ways to slow, hold, filter and/or infiltrate stormwater. Options include, but are not limited to the following: temporarily storing water on rooftops (generally not favored due to concerns about preserving waterproofing membranes atop buildings), creating green roofs to capture and use a portion of the precipitation that lands on a roof during storm events for watering vegetation (an increasingly popular but more expensive way to treat stormwater given the need for adequate structural support, excellent rooftop waterproofing, and other technical requirements), using cisterns and/or rain barrels to store rooftop or other surface water runoff, creating dry wells (holes in the ground filled with gravel) to move stormwater into the earth, creating bio-retention cells (areas typically having a combination of engineered soils, plants and mulch), installing porous pavement atop a compacted washed gravel base; and implementing rain-gardens (shallow depressions that collect water from nearby impervious surfaces and then infiltrate the water into existing, plant-mediated soils).<br><br> Stormwater Retrofitting Ideas by Tim Merklein (KSU-LA/RCP 2008) Residential Stormwater Retrofitting: An Educational Guidebook for Pottawatomie County, Kansas Timothy Merklein, Dept. of Landscape Architecture / Kansas State University - Capstone 2008 (pg. 43).<br><br> Steps to Create a Successful Rain-Garden In some ways creating a rain-garden can be as simple as A-B-C. A) Look for a good location; B) Dig a shallow depression to collect water from part of a rooftop, patio or driveway; and C) Plant vegetation that is well-adapted to the particular soils, climate/micro-climate, as well as the amount of water likely to be received by the garden. However, to make sure that you create a garden that relates well to its local and regional context and that will also last a good long time 4we suggest that you thoughtfully consider the following six steps in your process of designing and then creating a rain-garden.<br><br> The first three steps relate to carefully planning your garden while the second three relate to successfully implementing your plans. 1. Understand Your Property and Its Context 2.<br><br> Locate and Size Your Rain-Garden 3. Prepare a Place-Specific Rain-Garden Planting Design 4. Excavate and Prepare Soil for the Rain-Garden 5.<br><br> Install and Water Plants 6. Monitor and Care for Your Rain-Garden The following pages of this guidebook describe important ideas related to these six steps. Adapting the ideas in this guidebook to your specific context will help you address the issues relevant to your property and thus create a rain-garden that responds to the unique soils, micro- climate, and other factors associated with your community and bio-region.<br><br> We wish you the very best in your effort to reduce negative stormwater impacts while also creating habitat for birds, butterflies, people, and other fascinating creatures! Understanding Your Property and Its Context The first thing you should do as you plan your rain-garden project is to seek to really understand your property (its eco-regional and climatic context, topography/landform and hydrology or water flows, its micro-climate and sun-shade patterns, its soils and vegetation, and its immediate neighborhood and community context). You should also consider the variety of ways you can use to reduce stormwater impacts and help protect water quality downstream from your property.<br><br> In relation to better understanding your property and its context property owners should address the following questions: What eco-region do I live within, and what natural vegetative communities offer the best models for my property and rain-garden? Knowing what eco-region you are in gives you a much clearer idea of the types of plants that you should consider for your rain-garden, and this knowledge helps you avoid choosing invasive plant species that may compromise the ecosystems within your eco-region. For example, Manhattan, Kansas lies within the Flint Hills eco-region, which is considered to be globally significant (due to its biological diversity and integrity) and vulnerable to degradation by human activities (due to invasive plants and poor land development and management practices).<br><br> As you seek to reduce damaging stormwater runoff impacts, you do not want to negatively impact ecosystems in your region, so get to know your eco-regional context and find out about the species that are considered to be invasive in your area. What USDA Planting Zone do I live within? Knowing your plant hardiness zone will give you an understanding of the plants that will survive through the extreme temperatures associated with your winter climate.<br><br> Kansas shares two hardiness zones 3 with much of the southern half of the state in Zone 6a (where average annual minimum temperatures may drop to 5 to 10 below zero) and areas to the north in Zone 5b (where winter temperatures may drop to 10 to 15 below zero). What is also important to recognize that windy, hot Kansas can also seriously stress plants during the summer (especially in July and August), so it is important to consider moisture-loving plants that can adapt to periods of drought (unless your garden is protected by shade and has a high water table or you are willing to regularly water your garden during hot, dry periods). How does water flow across my property?<br><br> Topography (or landform) plays a major role in directing water across a property so you will want to consider how gentle or steeply sloping your property is. Rain-gardens should be located so as to capture flows of water from rooftops and downspouts, sidewalks, patios, driveways, and other impermeable surfaces. It is best to collect stormwater runoff before it concentrates into a rushing stream of water, otherwise it may cause erosion and wash away your plantings and mulch.<br><br> Steeply-sloped areas are generally not good places for rain-gardens (especially if they are continually carrying sediments into the rain- garden), although stair-step type gardens can certainly function as rain-gardens. The best way to observe the flows of water is to get outside in a rainstorm (or as the snow melts). You may see that you need several rain-gardens to capture surface-water runoff on your property.<br><br> What types of vegetation exist on my property, and what plants are abundant in the surrounding neighborhood and community? If you know your plants, documenting vegetation is not too hard. If you need help, find someone who knows plants or study up by going to the library and the Internet.<br><br> Vegetation that is within several hundred feet of your property may contribute seeds to your rain-garden, so it is helpful to know what kinds of plant species are growing in your neighborhood and the larger community. Some seeds will bring pleasant surprises, but most will require sweat equity as you pull unwelcome weeds. Learning about invasive species and the movement of seeds and other plant propagules (for example, how readily birds spread honeysuckle berries and the wind carries crabgrass seed) will help you address the inevitable growth of vegetation that you do not plant in your rain-garden.<br><br> What types of soil exist on my property? When it comes to understanding soils doing a few simple infiltration tests and testing or feeling the texture of the soils are very helpful. Because most rain-gardens are four to twelve inches deep, you need to make sure that water collected in the garden will infiltrate or evapo-transpire (evaporate into the air or be transpired by plants) within about 48 hours.<br><br> If your rain-garden dries out within two to four days it will not be a breeding ground for mosquitoes (they typically require at least four or more days of placid water to lay eggs and then metamorphose into adults). Infiltration will also increase as plants get established (assuming that the soil is not constantly being compacted or that the rain-garden is silted in with fine, soil clogging particles during or after construction). In the Flint Hills we have areas of heavy clay soils, but remember, these are great for retaining moisture and can be penetrated by the roots of native plants!<br><br> If someone tries to tell you not to plant a rain-garden in heavy clay soils have them take a look at KSU 9s International Student Center Rain-Garden where the soils were very dense, but with very little amending are now supporting many native grasses, sedges, and wildflowers. (Read more on the KSU-ISC Rain-Garden in Appendix A.) What type of micro-climate and sun-shade patterns does my property have? Knowing about topography (discussed earlier) helps you better understand the microclimates on your property.<br><br> South-facing slopes are hotter and north-facing slopes are cooler. Lower areas are typically moister (they collect surface water) and they may also be cooler as well. Shade trees temper temperature extremes, but trees may also limit the amount of rainfall landing on the garden (and trees can have extensive root systems that are hard to dig around or that you do not want to disturb).<br><br> Buildings and other structures also cast shade and alter the microclimate. If you pay close attention to what grows well in your neighborhood as well as in local natural areas you can learn much about how topography, soils, trees, and position influence microclimate and accompanying plant species and vegetative communities. While getting some fresh air and exercise take the time to observe your surroundings and this effort will pay off as you plan for your rain-garden.<br><br> As you can see, there is much to learn and think about! However, it is important to recognize that rain-garden design is not brain surgery. You do not have to be a scientist or expert in plants and natural systems to get things right.<br><br> You simply need to be willing to learn and explore, ask good questions, plan carefully, then implement your ideas. Remember, you are creating a garden and also learning to be a gardener. Since no garden maintains itself, dig in, and enjoy the experience!<br><br> You have the potential of creating a win-win-win situation (better water quality, improved physical and mental health, and the creation of a beautiful little ecosystem or two). Locating and Sizing a Rain-Garden Rain-Garden Location Rain-gardens function well in places where water is regularly moved away from your house 3 especially in locations downslope from downspouts, sump-pump outlets, and off of patios and driveways. You should not place a rain-garden where water would like migrate toward the house so areas downhill from buildings are best.<br><br> A rain-garden should typically be located at least 10 feet away from a building foundation (20 feet is best for structure/building with a basement) and at least three to four feet away from a driveway or road. You also need to make sure where tree roots, septic leach fields, water supply wells, and underground utilities are located so as not to disturb these. Call the local utility service clearance ( cOne Call d) to have utility lines marked.<br><br> Rain-gardens should not be created behind retaining walls not specifically designed to handle the extra weight and drain excess groundwater as they may cause these walls to fail. As you plan an appropriate location, consider how likely it would be for very fine sediments to be transported and accumulate in the rain-garden due to erosion. If rain-garden soils become sealed, water may stand in the garden for more than several days.<br><br> You do not want surface water to linger for four or more days as you will have a wetland and not a rain-garden. Thus, in many parts of the U.S. (especially in places having warm humid summers) it is not wise to locate rain- gardens in the very lowest spots of a property.<br><br> These areas generally stay too wet. In the Flint Hills eco-region the lowest areas of small developed properties (especially those one-acre to quarter-acre in size) typically do not stay too wet for too long during the growing season, especially if deep-rooted plants are growing in these locations or if the area is exposed to full sun for at least six hours a day. These conditions contribute to high evapotranspiration and infiltration rates.<br><br> Exceptions to this are low areas with a high watertable 4where groundwater is close to the soil surface. If possible, it is helpful to capture the first inch of rainfall and to assume that larger storms will fill your rain-garden up and then send additional stormwater away from the garden. No matter where your rain-garden is located you need to consider a way to reduce the erosive force of water as it enters and leaves your garden, and to make sure that the water does not stay around for more than two to three days.<br><br> Although many people like water to cdisappear d within a day, most plants can handle several days in standing water during the growing season, and mosquito breeding will not be a problem unless surface water lingers for four or more days. It is wise to look for a location where a flower garden would fit well with your property and where you can readily dig a shallow depression of the size and shape you want. If your ground is on a slope you will want to create a low earthen dam (or berm), a rock retaining wall, or a level- spreader (a level barrier or dam made of treated wood and/or rock) on the down-slope side of the rain garden.<br><br> A berm can be created by reusing the excavated soil from your rain-garden. On steep slopes (greater than 15 percent, or about a four-foot elevation change over a horizontal distance of 25 feet) you can create several stair-step rain-gardens or planting beds embraced on the downhill side by a low berm or a taller (perhaps one to two foot tall) dry-laid retaining wall. The drawings below show where to locate rain-gardens in relation to buildings and structures, driveways, walkways, patios, and areas of turfgrass.<br><br> You can direct water from downspouts and other collection points by pipe (underground or via surface flows) to each rain-garden. Rain-Garden Locations - drawn by Yun-Chieh [Jay] Chiu (KSU-MLA student 2008) Rain-Garden Sizing There are a number of ways to size your rain-garden and to determine the depth of your rain- garden. The most direct method we are aware of is presented below*.<br><br> Complete an infiltration test to determine the appropriate rain-garden depth and size your garden to meet your design intent including how much water you wish to collect. We suggest that you seek to capture and infiltrate the first inch of rainfall over a 24 to 48-hour period, modifying this approach to work with the specific limitations of your property. Follow the steps below to determine how deep your rain-garden needs to be to match the infiltration capacity of your soils.<br><br> Then determine the appropriate size of your rain-garden. Three-Step Infiltration Test: Step 1. Dig at least one hole (two holes may give you a better sense of infiltration rates for a proposed site but remember to average your two results).<br><br> Each hole should be eight inches in depth and diameter. Clean out the loose soil and fill each hole with water, allowing the water to soak into the soil for at least one hour. Step 2.<br><br> Fill the hole once again with water so that the water level is one inch below the top of the soil surface. Mark the top of the water level with a Popsicle stick, or other small stick (push the stick into the side of the hole flush with the water level). Record the time.<br><br> Step 3. Measure how far the water level in the hole drops at regular time intervals. For sandy soils check the water level every 15 minutes for at least an hour; for clay soils record water levels every 30 to 60 minutes for two to four hours.<br><br> Based on the infiltration rate measured, calculate how many inches of water will soak into the soil within 48 hours (two full days). The number of inches that soak into the ground over that period of time should be the maximum depth of your rain-garden, though it is wise to keep any rain-garden at a maximum depth of 12 inches. Infiltration Rate: ___ inches over 48 hours (determined by the infiltration test) Two-Step Sizing Determination: Step 1.<br><br> Measure the impervious area draining to the rain-garden (length x width, typically measured in square feet). As an example, if your impervious roof or driveway area is 50 feet by 20 feet then the impervious area for your rain-garden will be 1000 square feet. Step 2.<br><br> Using the information from the infiltration test, divide the impervious area by the rate of infiltration (in inches over a 48-hour period). Continuing the example above, if your soils can infiltrate 6 inches of water in 48 hours, divide 1000 by 6. This equals roughly 170 square feet of rain-garden or a 17 foot by 10 foot (or a 12 foot by 14 foot) area.<br><br> Rain-Garden Size: _____ square feet (impervious area / infiltration rate) * Source: Blue Thumb Guide to Raingardens ( Adapted from Schmidt, Shaw & Dods 2007, pages 11-14) Preparing a Place-Specific Rain-Garden Planting Design Selecting plants that are well adapted to regional and micro-climatic conditions and to the specific soil type within your rain-garden is very important. Thus, we encourage you to select native plants and to never use invasive species (which tend to be prolific reproducers and degrade natural ecosystems by crowding out less competitive native species). Why choose natives?<br><br> When planted in soils suited to their genetic memory regionally-adapted native plants can handle periods of drought and other climatic extremes and they need no fertilizers or supplemental watering once they are established. As a result, fewer inputs are needed over time, reducing costs and conserving resources. Native plants also host native butterflies and insects which increase biotic diversity.<br><br> Additionally, a number of native grasses and wildflowers have extensive root systems (and all natives have deeper roots than conventional lawns), adding organic matter and creating root channels for more rapid stormwater infiltration in all types of soil, including very dense clays. So prairie plants, especially those adapted to both dry and moist sites (such as mesic, moist or wet prairies), are excellent choices for rain-gardens in the Flint Hills eco-region. Konza Prairie 3 Prairie Root & Soil Systems (photo by Lee R.<br><br> Skabelund) Local Suppliers of Native Plants - A common challenge in some communities is finding local suppliers of native plants (unless there is a native plants nursery nearby or if you obtain permission to collect seed or live plants from native ecosystems). In urbanizing areas plant salvage (saving plants that might otherwise be plowed under due to expanding urban and suburban development) is possible. Note however, that many deep-rooted species are difficult to successfully transplant unless the individual plants are very young.<br><br> Sources of Plant Information One of the best sources for plant information nationwide is the USDA 9s PLANTS Database ( www.plants.usda.gov ). Konza Prairie is an excellent reference site and there are a number of excellent Internet sources, including several KSU-sponsored websites on prairie plants (for example: http://www.lib.ksu.edu/wildflower/ ). Native plants and ecological restoration nurseries are excellent sources of information regarding regionally-adapted plants which you can compare to what is listed on the PLANTS Database.<br><br> Examples of excellent online sources of native plant information include www.critsite.com and www.prairienursery.com . Prairie & Wetland (CritSite) Nursery (south of Kansas City, Missouri), Kaw River Restoration Nurseries (in Eudora, Kansas), and Bluebird Nursery (in Nebraska) are three nurseries that supply live plants and seed These nurseries were the primary sources of native plants for both the KSU-ISC Rain-Garden and the Rossville Rain-Garden. Native species 9 ranges can be checked through range maps at the PLANTS Database (which indicates if a species is found in your county).<br><br> The decision as to whether a plant is well-suited to a specific site should include an assessment of the moisture tolerance, soil type, slope, sun/shade preference, plant size and competitiveness, texture and seasonal interest, and attractiveness to wildlife (birds, butterflies, deer and rabbits). Konza Prairie 3 Buffalo Wallow (photo by Lee R. Skabelund) Discuss your interest in using plants native to your region with your local nursery.<br><br> If they cannot supply what you need, seek to obtain native plants from as close to your area as possible. Then, if needed, consider attractive, well-adapted, and non-invasive horticultural selections or cultivars. Plant & Planting Considerations Soil Moisture - Plant species that thrive primarily in moist soil conditions need to be placed in the deepest parts of the rain-garden, while species that thrive in dry soils can be placed on berms and side slopes, with species that prefer average soil moisture in-between.<br><br> As noted earlier, a number of prairie species have a wide range of moisture tolerances. Sun/Shade Preferences - Some plant species thrive in full sun, others in full shade. Most prairie species need at least a few hours of full sun each day and some species do best with at least six or more hours of direct sunlight each day.<br><br> Woodland species prefer full shade and can do very well in less than two hours of direct sunlight, generally early or late in the day when temperatures are cooler and the light is more diffuse. In the Flint Hills eco-region the plant palette is dominated by sun-loving species that can generally withstand prolonged periods of drought. This means that there tend to be fewer shade tolerant species, but they do exist.<br><br> Plant Height - The height of rain-garden plants can be significantly larger than they typically grow in their native habitats due to the increased amounts of concentrated water and more prolonged moisture levels. The tallest plants are often best placed in the center or deepest part of the rain-garden with smaller plants along the outside (so they are not buried from view). Choosing plants that fit the scale of residential, commercial, or institutional properties is important.<br><br> If native species are simply too tall for the specific setting, consider selecting dwarf varieties or shorter cultivars (or you may need to find other replacements). Grasses such as Switchgrass can be trimmed back early in the season to reduce their size. Flowers can clipped and used as cut flowers (which may be helpful in controling highly competitive species (including species such as Switchgrass Joe-Pye Weed, Sunflowers, Yellow Cone Flower, New England Aster, and other aggressive species).<br><br> Konza Prairie 3 Drought-Tolerant Wildflowers and Grasses (photo by Lee R. Skabelund) Flowering Time/Duration and Year-Round Interest - With forethought, your rain-garden can provide visual interest year-round 4spring, summer, fall and winter. Most nurseries have plant guides and brochures that discuss bloom time and duration.<br><br> Consider planting different species that will bloom at different times of the year, and also think about the winter coloration and structure of plants as well. Little Bluestem is stunning in summer, fall and winter. Dried coneflower heads, milkweed pods, and wild indigo stems and leaves each add a lovely winter effect.<br><br> Retaining some plants throughout the winter can provide visual interest, particularly right after snow and ice storms. Wildlife Value - Seasonal effects also influence use of the garden by wildlife and it is worth considering ways to invite butterflies and birds into the garden. Cardinal Flower and Blue Lobelia may attract hummingbirds to the garden.<br><br> Finches may come for coneflower seeds. There are many flowers that will attract butterflies, including Black-Eyed Susan, Blazing Star or Liatrus, and asters, milkweeds, and coneflowers. Monarch butterflies are particularly fond of milkweed species, and your garden could thus serve as a weigh station as these elegant creatures migrate north to Canada (for the summer) and south to Mexico (for winter).<br><br> Konza Prairie 3 Butterfly Weed and Monarch Butterfly (photos by Lee R. Skabelund) Salt Tolerance - Speaking of winter, if salt is used in the vicinity of rain-gardens (on roads or driveways) and you have heavy soils that will retain the salts in the soil system, then you will either need to eliminate or minimize the use of salts, or if this is not feasible, select salt-tolerant species. Otherwise your salt-sensitive species will likely disappear.<br><br> (Note that salt will also rapidly degrade limestone so avoid sparkling slat near limestone retaining walls or permeable pathways made of limestone.) Excavating and Preparing Soil for the Rain-Garden A rain-garden can be composed of a single pool, or several pools, depending on the slope of your property, the amount of water to be detained, and your aesthetic intent. Several step-pools can function very well on steeper slopes. Whatever your situation, it is important to create a garden that fits well with your property and with the structures and other elements on the property 4so laying out the garden is just as much a design exercise as drawing it on paper or the computer.<br><br> The rain-garden sketch below shows what a simple rain-garden looks like and also provides information about important design considerations. Rain-Garden Cross Section - drawn by Yun-Chieh [Jay] Chiu (KSU-MLA student 2008) Once you have selected a location for your rain-garden and sketched out your ideas (digitally or on paper), lay out the garden using stakes and string, a rope, or a garden hose. You will want to use stakes, string, and a level (or surveying equipment if you have access to them) to make sure that your berm, retaining wall, or level-spreader on the low side of your garden will spread water evenly out along the top of the berm/wall/dam once your rain-garden fills with water in a large storm event.<br><br> Measure the width and length of the garden and make sure the layout fits as well as it can. Before excavating, remove the sod (for re-use elsewhere if possible) and/or other vegetation. If your rain-garden site is full of weedy grasses or other undesirable vegetation you may need to take extra precautions to avoid spreading weedy vegetation (for example, rhizomes and runners from Bermuda Grass and other species can re-sprout and be nuisance for years to come).<br><br> Begin digging (using a shovel or roto-tiller for small rain-gardens, or a machine such as a bobcat for larger areas). The basic shape should be a flat-bottomed depression with side slopes of about 3:1 (flatter if space is available). If the rain-garden is eight inches deep the side slopes should be roughly three times that long (24 inches).<br><br> As you construct the rain-garden consider how to temporarily release water from the garden while vegetation is getting established. Most young, shallow-rooted rain-garden plants don 9t tolerate standing water nearly as well as taller, mature, and deep-rooted plants. Protect inlet and outlet areas with rock (and possibly vegetation) to dissipate concentrated flows of water and minimize soil erosion.<br><br> Once the rain-garden is excavated you can begin to amend the soil with compost and/or topsoil (as needed). Soil tests can be performed by university or county extension offices and should be done if you do not have a good sense of the pH and nutrient content of your soil. If your soil percolates well (roughly eight or more inches per day) then you should not need amendments to encourage infiltration.<br><br> If your soils are heavy clays, very sandy, have been highly compacted, or have little topsoil it is wise to add some compost and topsoil (weed-free as much as possible). Organic matter is vital in retaining soil moisture and adding nutrients (for sandy soils) and can loosen soils for heavy clays. Compost and/or topsoil should be thoroughly incorporated into the top 3 to 12 inches of existing rain-garden soil, depending on what is practical to do for the soils on your property.<br><br> At the KSU-ISC Rain-Garden, clay soils were so dense and heavy that roto-tilling barely broke up the top two inches of soil. A very small amount of topsoil was added to the two pools or shallow rain-garden basins, but no compost. Nevertheless, the native species that were planted have done very well 4flourishing due to adequate rains and supplemental watering during the first summer, and needing no supplemental watering during the second season.<br><br> Impressively, in the second season, a number of plants reached four to six feet in height!!! KSU-ISC Rain-Garden 3 Tilling the Clay Soils in April 2007 (photo by Lee R. Skabelund) To keep turfgrass from creeping into the garden edging of some type may be needed.<br><br> There is no perfect solution here, but consider using rock (limestone is abundant in the Flint Hills and flat pieces can be laid to create a formal or informal edge while allowing for water to run into the rain-garden and a lawn mower to cut turfgrass along the edge). Other options are flexible metal or plastic edging (with stakes to secure the edging into the soil), cut rock, or treated wood. Burying edging of whatever type at least three to four inches deep is necessary to keep turfgrass roots from spreading under the edging, while the top of the edging must be flush with the turfgrass thatch to allow stormwater to flow over the edging and into the garden.<br><br> You should create an elegant way to move water into and out of the garden without eroding soils above or below the rain-garden. Rain-chains can move water from roof scuppers to the ground, or you can simply extend your downspout through a pipe or channel or onto a splash-pad or rocky area (with large enough rock, blocks, or stone at the outlet to dissipate the energy of fast- moving stormwater that flows off of structures and hard surfaces during thundershowers or other downpours). Pipes can be buried and then day-lighted to your rain-garden as long as they slope consistently downhill so the pipes will drain freely.<br><br> Water can also be moved across a simple grassed swale, moved through a created, temporary ccreek bed d (with intermittent waterfalls if elevation changes are sufficient), run through a gravel filled trench, or be conveyed across a driveway or walkway through a French-drain (a gutter-like feature, typically with a screen on top to keep debris from clogging the drain or gutter). At the KSU-ISC Rain-Garden a level-spreader was used to avoid concentrating stormwater flows on the downslope side of the garden during and after major storms. KSU-ISC Rain-Garden 3 Two-Cell Garden with Level-Spreader (photo by Lee R.<br><br> Skabelund) Installing and Watering Plants Although it is possible to use seed (and seeding should be considered for very large rain-gardens where seeds can be drilled or pressed firmly into the soil and thus not to be washed away during storm events) we recommend using live plugs or small pots. When planting smaller rain-gardens, and in locations where you need or desire more immediate visual results, planting species as plugs and pots will provide more immediate impact. (For seeds you will likely need to patiently wait two to three years for the plants to establish.) Plugs and pots come in different sizes 4with some coming in 72-plant or 36-plant trays, others in six or nine packs, and still others in individual two-, three-, four-, six-, or eight-inch pots, depending on the nursery.<br><br> Deep-cell plugs, with containers 1-2 inches wide and 5-6 inches deep are particularly good choices for plants with naturally deeper root systems. Large potted plants (1/2-gallon or 1-gallon sized) can experience transplanting shock, especially after coming from nurseries where they have received daily pampering. Root-bound pots and plugs should be avoided (although these may be better than plants with hardly any root to speak of).<br><br> Ask and look for high-quality plants, especially since you may pay several dollars (or more) per plant for some potted plants. When purchasing live plants, smaller plugs are the least expensive, while larger pots provide more instant visual effect. Once you have selected the species and number of plant you want to purchase for your rain- garden (refer to c Preparing a Place-Specific Rain-Garden Planting Design d and c Calculating the Number of Plants to Purchase d) you will need to lay out the plants in your excavated and fully prepared rain-garden, in accordance with the required spacing requirements.<br><br> Once you have placed the plants you can move things around to fit with things you could not clearly visualize in your minds-eye or on paper. Unless your project is part of a research project (where every plant needs to be placed in a specific location) feel free to experiment; this is gardening and you should be happy with the arrangement of plants! Also remember that no matter how specific you have been in your design, natural processes will redesign the garden year-to-year.<br><br> If you are using native plants you should not use fertilizers as they will typically favor weedy competitors rather than the native species you plant. If you wish to enhance the root growth of prairie species we suggest that you invest in mycorrhizal inoculum (tablets or powder), which can be added near to the base of the roots when you plant each individual live plant. These cGroLife" Planting Tablets d contained fragments of fungal mycelium and pieces of mycorrhizal roots capable of colonizing and assisting host plant roots.<br><br> We typically used one or two 7-gram tablets placed near the roots of each live plant installed within the KSU-ISC Rain-Garden. Minimize trampling or compacting rain-garden soils by using boards as bridges (placing them atop stable rocks, bricks, or blocks), reducing walk-through traffic, and placing mulch down, then pulling back the mulch in the area where you need to dig a hole for a plant. Calculating the Number of Plants to Purchase: To determine how many plants you will likely need you can look at the spacing requirements at www.critsite.com or in Chapter 9 of the Blue Thumb Guide to Raingardens and then calculate the number of plants you need by doing the following.<br><br> Step 1: Determine the total space needed by each plant, multiply the distance between plants within the rows (X) by the distance between the rows (Y). Example: A square planting pattern with plants spaced (on average) at 12 inches on center, X = 12 and Y = 12. Therefore, 12 × 12 = 144 square inches.<br><br> Step 2: Take the total number of square feet of planting area and multiply it by 144 to convert square feet to square inches. Example: The total square footage of the planting area is 100 ft2. Therefore, 100 × 144 = 14,400 square inches.<br><br> Step 3: Divide the total number of square inches by the total number of inches needed by each plant. Example: 14,400 in2 ÷ 144 in2 = 100 plants. Obviously your calculations will need to be adjusted for plants with different spacing requirements (which should be based upon the size of the plants at maturity), and it may be easier to sketch your ideas on paper and then count up the individual plants you need.<br><br> Using CADD (computer-aided design and drafting) can also allow you to quickly calculate total plants for different areas given certain spacing requirement. Yet another other option is to choose the plants you want, find out if they are available, and then simply stake out the location of each plant in your designated rain-garden location, than count up the number of plant you need to purchase. KSU-ISC Rain-Garden 3 Planting the Two Pools in April 2007 (photo by Lee R.<br><br> Skabelund) Planting Techniques: Keep plant roots moist before planting; don 9t let them dry out by keeping plants out of hot, windy locations for long periods and watering them as necessary. If plants are root bound in pots unwrap the roots (and if this doesn 9t work make a few cuts down the side to loosen the roots). Do not allow the roots to dry out after taking them out of the pots; it is best to pull plants out of trays and pots one at a time.<br><br> Dig a hole large enough to allow the roots of each plant to hang vertically in the hole; do not plant roots in a J-shape as this will increase the stress on the plant. A small mound at the bottom center can be formed so roots can drape over it. Plant so that the base of the stem is slightly higher than the surface of the ground and make sure that the root ball is completely covered by soil, gently backfill the hole and then firmly push the adjacent soil around the root.<br><br> Do not leave air pockets around the roots. Give the roots of each plant a gently and thorough soaking. Add about 2-3 inches of shredded hardwood mulch (or another readily-available type of mulch that will not float away or quickly decompose; a good layer of leaf mulch is acceptable if this is the best option you have).<br><br> In placing mulch around each plant, keep a distance of about one inch around the base of plants so that the stems will not get scratched up. Press your finger in the soil around a plant or two during a dry-spell to check on soil moisture and water the plants in your rain-garden whenever the soil begins to dry out during the first growing season. Typically, new plantings need about one inch of water per week.<br><br> KSU-ISC Rain-Garden 3 Planting Native Grasses in June 2007 (photo by Lee R. Skabelund) Monitoring and Caring for Your Rain-Garden Weeding is a necessary part of gardening and the time spent weeding can be a great opportunity for each of us to learn about the dynamic nature of perennial plants (how quickly and abundantly they grow and propagate and how they compete with one another), other invading plants, as well as the influences of wildlife (including squirrels, rabbits, voles, moles, butterflies, moths, bees, birds, beetles, ants, and a multitude of insects), changing climatic conditions, the effects of flowing and infiltrating stormwater, and other factors. Larger rain-gardens having plenty of weeds or invasive species nearby the rain-garden will naturally require regular monitoring and weeding, especially during the first two years as the desired rain-garden plants fill in.<br><br> Smaller rain-gardens, surrounded by non-invasive turfgrass and few weedy species, will require much less care in terms of weeding. The key is to remove weeds before they release their seeds and so regular monitoring is needed. After the first growing season, native plants and other well-adapted plants should need no supplemental watering 4unless the rain-garden experiences a prolonged dry period, or if plants requiring consistently wet soils were planted in the garden.<br><br> Plants located under the canopy of trees may need extra water as they will likely not receive the same amount of rainfall that plants in the open receive. Annual Maintenance: It is helpful to keep a record of changes that occur in your rain-garden so that you know when to complete certain maintenance activities and to provide insights for others contemplating the creation of a rain-garden on their property. Just as with any perennial garden, weeding will be required throughout the season as will some clipping and deadheading of old flowerheads.<br><br> Plants that are prolific seed producers may need to be clipped back once or several times so to minimize the number of seeds released. Plants that get too large may need to be cut back or removed and replaced with more appropriate plants. Many species can remain over winter and then be cut back each spring (in March or early April) depending on the look that is desired.<br><br> If sediments, leaves, or other debris accumulates then these can be cleaned up. This will be needed if such elements pile up where water is entering the garden, especially if it begins to form a dam or barrier. Over time, less weeding should be required (especially after the second or third growing season) and you should learn when you need to look for certain kinds of weeds.<br><br> If you retain a three-inch layer of mulch in the rain-garden, weeds will be limited and when they are present will be easier to remove. As time progresses, you may see that water infiltrates quite rapidly and you may then be able to raise the berm or dam on the downhill side in order to capture and hold more stormwater. Common Rain-Garden Questions & Answers Can I plant a rain-garden on heavy clay soils?<br><br> Yes, especially if you choose native plants that are adapted to heavy clays and to the other specific conditions that your property and rain-garden site provide. You may want to amend the soils with topsoil and compost, thoroughly incorporating these additions into the clay soil via tilling as deep as the soils allow. This is especially important if the clays within your rain-garden site are fairly raw sub-soils (with little organic matter residing in them).<br><br> If this is the case make sure you over-dig soils by 6-12 inches (after rough-grading the rain-garden basin), then till compost and topsoil into these raw clays. You may also need to minimize the amount of water held in the garden during initial plant establishment by creating a notch or passageway in the downslope berm, the level-spreader, or retaining wall, then, as rain-garden vegetation matures, plant roots penetrate into the clays, and infiltration increases, you can fill in the opening (and possibly raise the downslope berm, level- spreader, or wall to collect even more water). What is the cost of a rain-garden?<br><br> Costs could be as little as $500 for a 200-300 square foot garden (perhaps $2-5 per square foot if you do the work yourself, and use smaller plants, mulch, and salvaged rock) or perhaps twice as much if you use larger plants and use additional features. Nevertheless, a rain-garden can pay for itself in landscape value. More important than cost, rain- gardens add beauty to both the homeowner 9s yard and the neighborhood.<br><br> Imagine driving down a street and seeing lovely gardens in every yard or on every property. Rain-gardens allow homeowners to create a perennial garden for a modest cost 4and these gardens are well-watered whenever it rains. Will my rain-garden look weedy?<br><br> How can I make my rain-garden look acceptable to neighbors, homeowner associations, and community officials who want every property looking neat and tidy? How often should I weed and water my rain-garden? By building in cues that show you intentionally planned, implemented, and are caring for the rain-garden you will create a perennial garden that is appreciated by your neighbors and other community members.<br><br> Massing certain species (with at least three or more plants clustered together) can help, as can repeating patterns, relating to nearby architectural features, and the creation of well- defined edges. Placing tall plants in back of smaller plants (in stair-step fashion) and framing the garden (with a fence, limestone wall, decorative rock, pathway and/or sitting area) can also help make the garden look very acceptable. Weediness is in the eye of the beholder, but regular weeding and selective pruning will minimize this concern.<br><br> How much time will it take for the rain-garden to establish? If you use live plants and plant early in the spring then the rain-garden could really take off in the first growing season. However, it will take at least 2-3 growing seasons for a rain-garden to really fill in.<br><br> What about mosquitos? The most common question about rain-gardens are about possible mosquito breeding. In a properly designed garden, water should be properly soaked away after 24-48 hours.<br><br> Mosquito larvae will not have enough time to complete their life-cycle before their potential breeding ground dries up. Although it is unlikely, if water ponds for 3-4 days, then the surface of your rain-garden has sealed up; it will need to be loosened to allow for infiltration. Appendices Case Studies 3 The KSU-ISC and Rossville rain gardens highlight relatively simple ways to reduce storm-water runoff and improve the water quality of local streams.<br><br> Both rain-gardens were designed by KSU faculty and students in the Department of Landscape Architecture / Regional & Community Planning. Professor Lee R. Skabelund played a primary role in the design of both rain-gardens and is the contact at KSU (firstname.lastname@example.org).<br><br> KSU 9s International Student Center (ISC) Rain-Garden Project Location and Description: The KSU-ISC Rain-Garden is located near the Campus Creek corridor, upstream from the Quinlan Natural Area and south of the Vet-Med Campus, at Kansas State University. Planning, Design & Construction Process: PROJECT GOAL: Create a rain-garden and streambank improvements along a target area of Campus Creek at Kansas State University to improve to the environmental setting and reduce stormwater run-off. Demonstrate specific ways to address urban stormwater runoff to KSU administrators, staff, faculty, students, and visitors.<br><br> METHODS: 1) Develop graphic plans/designs for a rain-garden and streambank improvements along Campus Creek by hosting introductory integrated stormwater management and design presentations and holding a one-day design charrette. 2) Engage KSU administrators, staff, faculty, and students in a discussion of water quality concerns and solutions related to urban stormwater runoff. Work with landscape architects and other professionals to formulate plans and designs for this area of Campus Creek.<br><br> Complete detailed plans/designs for a rain-garden and streambank improvements. Coordinate basic pre and post-construction water quality monitoring to highlight before and after conditions. 3) Secure approvals, equipment, materials, and participation; and complete other construction planning and coordination.<br><br> 4) Use volunteer labor and donated materials/vegetation to create a rain-garden above Campus Creek in order to reduce stormwater inputs from a small area of adjacent roadway and upslope buildings/parking areas. 5) In tandem with method #4, initiate minor streambank improvements along a small, adjacent portion of Campus Creek. http://faculty.capd.ksu.edu/lskab/raingarden.html Rain-Garden Design (Concept Drawings): KSU-ISC Rain-Garden 3 Perspective Sketch by Cary Thomsen (January 2007) KSU-ISC Rain-Garden 3 Plan View Sketch by Lee R.<br><br> Skabelund (February 2007) Rain-Garden Design (Final Drawings): KSU-ISC Rain-Garden 3 Section by Cary Thomsen (February 2007) KSU-ISC Rain-Garden 3 Plan View by Cary Thomsen (March 2007) Rain-Garden Construction: Work included the following construction activities: grade two shallow basins; relocate four existing shrubs; install nine large pieces of limestone (to respond to ISC architecture, allow access through the rain-garden, and provide seating); place weed barrier and washed filter-stone down as the base for two pathways; place three large limestone csplash-pads d atop the three silted-in dry wells; construct a level-spreader (to minimize concentrated flows as water exits the rain-garden); haul and place topsoil along the fringe of the basins; rototill soils and beds in preparation for planting; plant approximately 250 dry to wet prairie and a few wetland plants (representing, for the most part, species common to the Flint Hills Eco-region); plant additional perennials and shrubs; mulch all planted areas; and, repair the flagstone path (which was damaged while under construction by two very heavy May 2007 rain events). KSU-ISC Rain-Garden 3 Construction began with rough-grading using a skid loader, placing limestone, and creating porous pathways (March 2007 photos by Lee R. Skabelund) Rain-Garden Plant Species Selection: Given the visibility of this demonstration project 30-40 hours of time was spent determining what species to use for the KSU-ISC Rain-Garden.<br><br> This included time to research specific plant characteristics (including root structure, flowering color, timing, and duration, soil chemistry and moisture preferences, sun/shade preferences, etc.), to check plant information at various websites (CritSite/Prairie & Wetland Nursery was especially helpful, as was Prairie Nursery 9s list of plants for heavy clay soils), and then to cross-check findings with the USDA Plants Database (to see which species were found in Riley County, Kansas). A number of hours were required to correspond with nurseries about plant availability, to consider specific nursery recommendations, to adjust and finalize plant lists when preferred species were not available, and to make final plant orders from Prairie & Wetland Nursery (western Missouri), Kaw River Restoration Nursery (eastern Kansas), and Bluebird Nursery (central Nebraska). Additional Plantings 3 Sun and Shade Perennials, Herbs and Shrubs Because the scope of the project went well beyond the area within the two rain-garden cells or pools, additional mulch and plants were obtained to cover, stabilize, and enhance the visual and experiential quality of the project site.<br><br> Plants (some native, some cultivars, and a number of ornamental species) were selected on-site at Blueville Nursery, Riley County 9s largest retail nursery and these were planted in areas surrounding the KSU-ISC Rain-Garden. KSU-ISC Rain-Garden 3 Pools Filled with Rainwater (June 2007 photo by Lee R. Skabelund) KSU-ISC Rain-Garden Plant List: Ongoing Monitoring & Maintenance: First year watering and weeding occurred on a regular basis 3with 30-gallon garbage cans being used for several months to catch a portion of rooftop runoff and to simplify watering.<br><br> A garden hose was also used to water the garden during drier periods (especially July and August 2007). Because of the amount of weedy grasses and other herbaceous weeds in the vicinity as well as the prolific number of berries produced by adjacent honeysuckle and buckthorn, ongoing monitoring and weeding requirements at the KSU-ISC Rain-Garden have been quite demanding. Training of students has occurred on several occasions, however the lion 9s share of weeding has been done by Professor Lee Skabelund, who has been attempting to get a detailed and accurate idea of monitoring and maintenance requirements for this garden.<br><br> During the period of May to July 2008 approximately 40 hours of volunteer time were contributed by KSU students and faculty for weeding, spot watering (discussed below), and branch and debris cleanup (including work to cleanup the garden, rooftop, and adjacent area after the June 10 , 2008 EF1 tornado moved over the ISC). Fortunately, the 25-foot branch that was tossed into the rain-garden did very little damage (but highlights the uncertainties of climatic extremes on the Great Plains). Except for the watering of transplanted vegetation along the fringe of the rain-garden, and occasionally watering plants in higher and drier settings, no supplemental watering has occurred within the rain-garden during the 2008 (or second full) growing season.<br><br> Abundant June 2008 rains created very rapid growth of rain-garden and fringe area prairie species, with some plants reaching five to six feet in height by late June and July. As of this writing (early August 2008) no watering of the rain-garden has occurred. It is possible that over time, some of the sedges which require higher soil moisture levels (and which typically are found in east of Lawrence, Kansas) will be replaced by the more hardy Flint Hills prairie species, however, time will tell.<br><br> KSU-ISC Rain-Garden 3 August 12, 2007 (photo by Lee R. Skabelund) Special Features: Two-Cell Rain Garden with Level-Spreader The KSU-ISC Rain-Garden has two cells or pools. The pool closest to the ISC 9s Taiwan Wing is shadier (lying partially under the north side of a very large American Sycamore), slightly deeper (about 12 inches at its deepest), and moister (collecting all the rooftop runoff from very small storms and receiving the first flows of rooftop runoff from all storms) than the pool closest to Campus Creek.<br><br> The second pool was created by scooping out 6 to 8 inches of soil and creating a level-spreader on the downslope (or Campus Creek) side of the garden. The level-spreader is in essence a semi-leaky dam, created by using two 2x12-inch treated boards, 10 feet in length, placed end to end and backed by 50-70 pound pieces of salvaged limestone from the Bayer Stone Yard in Manhattan). The level-spreader is leaky because it was lowered after its initial installation (we were concerned that in a major storm water could back up to close to the at- grade foundation of the Taiwan Wing) and the gravel that was placed at the bottom of the level- spreader was intermixed with the sticky clay soils.<br><br> Because it was surveyed in by its designer (Professor Dennis Day) it is nearly perfectly level and thus serves its purpose very well (to spread water out over its entire length in a major storm, thus reducing the chance for concentrated and higher velocity flows leaving the garden. The two pools are separated by a several inch rise of earth and three large pieces of cut limestone, which serve as a pathway through the middle of the garden. Water enters the upper pool by falling from scuppers unto one of three large cut limestone splash-pads (salvaged from the Bayer Stone Yard) or into one of three metal rain-bowls (created and installed by Professor Casey Westbrook 9s sculpture students).<br><br> During larger storm events, surface water also moves from the east (or back) side of the Taiwan wing, flows through a wide pathway of gravel and limestone path on the south side of the Taiwan Wing (under the Sycamore), and enters the lower pool at it its southeast corner. Porous Pathways Two porous (permeable) pathways were created on either side of the rain-garden. A more formal pathway was created to reflect the formality of the ISC courtyard and the eight- foot grid of the ISC architecture.<br><br> This pathway sits on heavy clay, scraped clean of turf by a skid- loader. A root barrier/filter fabric was placed atop the clay, then 2-4 inches of washed ½ to ¾ inch gravel was laid down, followed by salvaged cut limestone squares and rectangles, voids between the cut limestone were filled with smaller limestone gravel (up to about ¼ inch in size). The pattern, designed in the field after we discovered that we had different sizes of cut stone, has the feel of an oriental tapestry (at least that is the perception of some visitors to the garden).<br><br> An informal flagstone pathway runs along the south side of the Taiwan Wing and rain-garden and conveys people and stormwater without eroding the underlying soils (which was a problem prior to rain-garden construction). This pathway was created by digging out a shallow swale, covering the soil with a root barrier/filter fabric, adding washed ½ to ¾ inch gravel and then placing irregular-shaped pieces of limestone (called flagstone by the supplier) in a manner that would lock them together, starting from the bottom (next to the level-spreader) and working up past the southeast corner of the Taiwan Wing. Once all of the flagstone was securely in place water flowed through the network of voids.<br><br> Some gravel is moved during heavy downpours, which brings concentrated flows of water from KSU 9s Derby Dining Complex and the open area of trees, shrubs, and turfgrass east of the ISC. Project Cost: Financial support for the ISC Rain-Garden Design/Build Project was provided by WaterLINK and KDHE Clean Water Neighbors grants. In-kind donations and volunteer labor were provided by KSU 9s College of Architecture, Planning and Design, KSU Facilities & Grounds, KSU faculty, students and staff, KSU 9s Art Department, The Civitas Group, Bayer Stone, Midwest Concrete Materials, Higgins Stone, Coonrod Construction, Atwood Rentals, Blueville Nursery, CritSite Prairie & Wetland Nursery, Bluebird Nursery, Kaw River Restoration Nurseries, and Three Rivers Engraving.<br><br> In-kind volunteer time likely exceeds $10,000 for the project. ISC Rain-Garden Project (Spring 2007 - Summer 2008) - WaterLINK Expenses Purchases made for the ISC Rain-Garden Design/Build Project The Civitas Group (preliminary grading of rain-garden basins) - $78.75 Bayer Construction (delivered washed filter stone & topsoil) - $362.46 + $85.00 Higgins Stone (delivered flagstone and Dover shell limestone strips) - $1,217.00 + $221.00 Atwood Rentals (work gloves & rental of tools) - $23.60 + $61.48 Horticultural Services (weed barrier & metal pins) - $150.95 Crit Site Prairie & Wetland Nursery (rain-garden plants & mycorrhizal inoculum) - $1,014.39 Applied Ecological Services/Kaw River Restoration Nurseries (prairie plants) - $240.00 Blueville Nursery (plants, stone & mulch) - $196.89 + $157.78 Bluebird Nursery (supplemental prairie grasses) - $98.17 KSU Motor-Pool (van rental transportation of plants from CritSite) - $123.48 Three Rivers Engraving (long-lasting bronze tone rain-garden sign) - $800.00 Lee Skabelund purchases & reimbursements (Home Depot 3 lumber; Blueville Nursery - plants) - $84.49 (Westside Market - plants) - $67.42 Total Expenses - $4,982.86 Rain Bowl Material Costs (Spring 2008) - $2,059.12 Donations made to the ISC Rain-Garden Design/Build Project The Civitas Group (tools & consultation time) - $407.50 Bayer Stone (stone & consultation time) - $3,000.00 Midwest Materials & Concrete (loading & hauling stone from Bayer Stone Yard) - $450.00 Coonrod & Associates Construction Company (off-loading stone at the ISC) - $295.00 Atwood Rentals (donation of tools for multiple work-days) - $745.00 Kaw River Restoration Nurseries (prairie plants) - $50.00 Blueville Nursery (5 cubic yards of mulch) - $200.00 Three Rivers Engraving (rain-garden sign) - $58.00 KSU Facilities & Grounds (use of skid-loader for nine days, in-kind time by several Grounds personnel, and consultation time by J. Toburen, M Taussig, J.<br><br> Myers, and D. Berner) - $1,250.40 Total Donations (by external partners and non-academic departments): $6,455.90 Addt 9l Donations by KSU College of Architecture, Planning & Design, Dept. of Art, and other departments: Use of truck and tools for multiple workdays; use of four garbage cans) Volunteer time by ~75 KSU students, staff & faculty between January and July 2008 Note: A $10,000 KDHE Clean Water Neighbors Grant covered a small portion of salary for Lee Skabelund and a small amount of wages for Cary Thomsen (for work accomplished during Spring and Summer 2007).<br><br> Project Team: Project Manager: Professor Lee R. Skabelund, ASLA (KSU-LA/RCP) Lead Designers: Professor Lee R. Skabelund and Cary Thomsen (KSU-MLA 2007) Level Spreader Designer: Professor Dennis Day Construction Workers: KSU-LA/RCP faculty and students 4working with other KSU volunteers and local businesses.<br><br> For example, Midwest Concrete Materials hauled stone from the Bayer Stone Yard to the ISC, and Coonrod Constr