M100602D - Memex II Memory Upgrade for Fanuc 0 Manual

To view this page ensure that Adobe Flash Player version 9.0.124 or greater is installed.

Please login or register to make a comment!

...Description...... more. less.

SRAM for Fanuc ® Series 0-A, 0-B and 0-C controls. The 0-A control can be upgraded 48K (120 meters), while the 0-B, 0-C and the 0-4PC controls can be upgraded with 128K (320 meters). The SRAM based memory is located in sockets on either the Main CPU board (0-A and 0-B) or on the Memory Card (0-C and 0-4PC) as illustrated on pages 4 and 5. The supplied IC 9s (integrated circuits) will be used to add to the existing SRAM on these boards. These instructions will assist you in completing the memory upgrade for your Fanuc 0 Series control. Please read through this document completely to familiarize yourself with the installation before actually performing your upgrade. Applicable Master Boards 0-A 0-B 0-C / 0-4PC A16B-1010-0150 A16B-1010-0280 A20B-1002-0360 A16B-1010-0210 A16B-1010-0281 A20B-1003-0750 A16B-1010-0240 A16B-1010-0285 A20B-2000-0175 A16B-1010-0286 A20B-2000-0179 A20B-2000-0180 Sample cB d Software Versions: 415, 815& Applicable Memory Cards (0-C and 0-4PC) Memory Cards A16B-1212-0210 Analog Spindle (MEM-A3) A16B-2201-0103 Analog Spindle A16B-1212-0215 16 bit, Serial Spindle A16B-1212-0216 32 bit, Serial Spindle A16B-2201-0101 32 bit, Serial Spindle Sample cC d Software Versions: 460,462,465,660,662,690,665,880,135& Chapter 2 3 The Basics M100602D Copyright © Memex Automation Inc. 2004 - 2007 Page 4 of 19 Locating SRAM Modules (0-A / 0-B) I/O BA4 CAP CV21 CF91 CV22 CF92 CA1 CA2 PAS SO SI WDA (4H) (3H) (2H) (1H) (34L) (34H) Memory Modules (4L) (3L) (2L) (1L) A16B-1010-0150 (Analog) A16B-1010-0210 (Digital) A16B-1010-0240 (0-Mate) Memory Modules CS8 CPA4 CP11 CCX M3 M2 M49 M48 M47 PAS (1H) (2H) (3H) (1L) (2L) (3L) M46 M45 M44 M39 M38 M36 M36 M35 M34 M26 M27 M25 M74 CS7 CS3 CS2 (34H) (34L) (12H) (12L) Battery connection A16B-1010-0280 A16B-1010-0281 A16B-1010-0285 A16B-1010-0286 Chapter 2 3 The Basics M100602D Copyright © Memex Automation Inc. 2004 - 2007 Page 5 of 19 Locating MEM-A3 Card (0-C / 0-4PC) Locating SRAM Modules (0-C / 0-4PC) M27 M12 M26 M3 CCX5 M5 M74 CPA7 (2H) (2L) (3H) (3L) Power Supply Memory Card A16B-1212-0210 A16B-1212-0215 A16B-1212-0216 A16B-2201-0101 A16B-2201-0103 Memory Modules Battery Connection Chapter 2 3 The Basics M100602D Copyright © Memex Automation Inc. 2004 - 2007 Page 6 of 19 The Basics Installation Considerations The installation of the SRAM modules should be conducted with care. Never install or remove a board with the control power on (the main power can be on, but not the control). Take care with the handling of the integrated circuits, as they are static sensitive. Do not place the IC 9s in any other sockets than as per pages 4 and 5. Do not force, drop or otherwise mishandle the modules during the installation procedure and always check the functionality of the machine at the end of the installation (i.e. move the axes, perform a tool change, run a program, etc.). Backup Critical Parameters For series 0-A, 0-B, 0-C and 0-4PC upgrades it is very important that you have a hard copy back- up of all your control 9s critical parameters. The following instructions will assist you in dumping a majority of the Fanuc 9s parameters to a PC to be saved. However, it is still advised to keep or make, if you haven 9t already, a written copy of ALL the critical parameters. You can use the Parameter Sheets in the Appendix of this manual to write down all Settings, PC and Diagnostics parameters. All of the Diagnostic parameters between D300 and D600 must be written down here. Be sure that all of the files you downloaded have been successfully recorded and saved on your computer before performing the upgrade to your control. Otherwise you will have no choice but to enter ALL parameters by hand in MDI. Verify Your Control Once the memory modules have been installed and all parameters have been restored, satisfy yourself that the control is working properly. Test the machine by the following procedure through either MDI or program: " Home all axes, tool-changers and pallets 3 check for need to reset Absolute Pulse Coders here. " Check spindle functionality through all speeds and gear ranges. " Check also Clockwise and Counter-clockwise rotation with M3 and M4 commands. " Check the tool changer. Be sure that the tool you received was the tool requested and that the carousel rotates in the proper direction. " Check the pallet changer (if applicable). If your machine requires special custom macros for a pallet changer or tool changer, be sure that they have been loaded. Once your machine has been proven, you have successfully upgraded your control. Chapter 3 3 Installation for Fanuc ® 0 M100602D Copyright © Memex Automation Inc. 2004 - 2007 Page 7 of 19 Installation for Fanuc ® ®® ® 0 Backup Your Control Before starting the installation, power on the control and verify that the machine tool is in good working order. I. Parameter Settings for Punching Set up the following communication parameters for the desired CNC port. Please make note of the original settings for proper restoration of the new memory (see page 16). On the SETTINGS (HANDY) screen, set the following: TVON = 0 (TV Check off) ISO = 1 (ISO data format) I/O = 0 (port number) PWE = 0 (Parameter Write Enable OFF) TAPE = 0 Write down the previous settings so that they can be restored upon completing the upgrade. Also set the following parameters: Chart 1 CNC Parameter Port 1-M5 I/O=0 Port 1-M5 I/O=1 Port 2-M74 I/O=2 Port 2-M74 I/O=3 Current Settings 0002 1xxxxxx0 -- -- -- 0012 -- 1xxxxxx0 -- -- 0038 10xxxxxx 10xxxxxx xx10xxxx xx10xxxx 0050 -- -- 1xxx0xx0 -- 0051 -- -- -- 1xxx0xx0 0250* -- -- 10 -- 0251* -- -- -- 10 0552* 10 -- -- -- 0553* -- 10 -- -- * Parameters 250, 251, 552 and 553 represent the baud rate during communication and are set here to 4800 baud. Parameter 552 is used if Setting I/O=0, 553 if I/O=1, 250 if I/O=2 and 251 if I/O=3. The protocol is Even parity, 7 data bits and 1 stop bit. For more baud rate choices refer to the following Chart 2. Chapter 3 3 Installation for Fanuc ® 0 M100602D Copyright © Memex Automation Inc. 2004 - 2007 Page 8 of 19 Trace the RS-232 cable from the serial port connector back to the CNC MEMORY PCB to determine if you are connected to Port 1 (M5) or Port 2 (M74). Then, label the serial port connection so it is visible from the outside. Chart 2 for Serial Baud Parameter on 552/553 or 250/251 Parameter Value Baud Rate 1 50 2 100 3 110 4 150 5 200 6 300 7 600 8 1200 9 2400 10 4800 11 9600 II. PUNCHING CNC NC PARAMETERS (CNC - PC) " Connect the Fanuc serial cable between the serial ports on your computer and the CNC. " Set up your computer with a terminal software program (Telix / ProCom+ / Hyper Terminal). " Perform the following steps on the PC and CNC as follows: PC-- Using the Baud Rate set in parameters 552 & 553, Even parity, 7 Data bits and 1 Stop bits, set your terminal program to receive a file. PC-- Enter a file name to record the NC parameters. ie; #103.NCP (103 being the machine #) CNC-- Go into EDIT mode. CNC-- Make sure the cMemory Protect d key is off. CNC-- Press DGNOS/PARAM, [PARAM], then hold EOB while you press OUTPUT/START. Hold the EOB key while pressing the OUTPUT/START key to punch ALL the NC Parameters, including the 900 level options. (The CNC will flash OUTPUT in the lower right corner of the CRT.) (The PC will display the text and count lines until finished.) PC-- Save the file you just received from the CNC on the computer. IMPORTANT: Check the .NCP file with a text editor to visually confirm that system parameters N0900 series have been sent to the computer. If these parameters are not found in your listing, please repeat this section (Punching CNC Parameters). Take this moment to write down the 900 level system parameters for backup purposes. Comment [WLB1]: Chapter 3 3 Installation for Fanuc ® 0 M100602D Copyright © Memex Automation Inc. 2004 - 2007 Page 9 of 19 III. RECORD THE PMC PARAMETERS You must manually copy down on paper ALL of the Diagnostic parameters between No. 300 3 600 (see page 18). These parameters represent the Timers, Counter, Keep Relays & Data Tables used by the machine builder. On the Fanuc 0-C you can punch these PMC parameters. This backup is necessary before continuing this memory upgrade. Be sure that all of the files above have been successfully recorded or saved on your computer. If there is any doubt, please contact Memex Automation before continuing. Some parameters are changing, ignore these 3 generally it is every 5 th one that you need as you can see on the attached chart. Sample Fanuc 0-C PMC Parameter Dump _&??:_% < 2 2 Delete the feed info before the first % sign 10300 00101000 10301 00000000 10302 00000000 10303 00000000 10304 00000000 10305 00001010 10306 00000000 10307 00001111 10308 10001111 & 10597 00000000 10598 00000000 10599 00000000 %_ IV. PUNCHING CNC PART PROGRAMS (CNC - PC) " Ensure that NC Parameter 10 bit 4 = 0 (xxx0xxxx) so that ALL programs can be backed up properly (including the 9000 macros). " Perform the following steps on the PC and CNC as follows: PC-- Enter a file name to receive the NC parameters. ie; #103.PRG (103 being the machine #) CNC-- In EDIT mode, with the cMemory Protect d key off, press PRGRM, [LIB], O-9999, then OUTPUT/START. PC-- Save the file you just received from the CNC on the computer. V. PUNCHING CNC TOOL OFFSETS (CNC - PC) " Perform the following steps on the PC and CNC as follows: PC-- Enter a file name to receive the NC parameters. ie; #103.TOF (103 being the machine #) CNC-- In EDIT mode, with the cMemory Protect d key off, press OFFSET, and then OUTPUT/START. PC-- Save the file you just received from the CNC on the computer. Chapter 3 3 Installation for Fanuc ® 0 M100602D Copyright © Memex Automation Inc. 2004 - 2007 Page 10 of 19 Installation Procedures for Fanuc ® ®® ® 0 At this time you should run the Memex upgrade software provided on the diskette included with your manual. Place the diskette in the A drive on your computer. Go to the Start menu and click on R un.. Type [A:\UPGD0.EXE], then [OK] or at the DOS prompt type [A:], then [Enter] followed by [UPGD0], then [Enter]. After viewing the acknowledgment screen, press F3 to open the .NCP (parameter) file that you received from your control. Press F9 to perform the upgrade on your file. After the software has performed the upgrade successfully, exit the software by pressing Alt-X. If the software gives you a message that the upgrade was not completed successfully, you will have to re-send the NC parameter file, from your CNC, to your computer. Make a print out of your .NCP parameter file. When you are confident that you have completely saved all of your CNC information, you will be ready to proceed with your memory upgrade . The part program and system memory is located on the Master Board for Fanuc 0-A and 0-B Series controls and on the MEM-A3 card for 0-C and 0-4PC Series (see pages 4-5). Locate this board in your machine control cabinet. " Check that you have received all of the information out of your CNC control. Check also that any Custom Macro Variables have been written down and recorded. 1. Power OFF the control and the machine. Open the cabinet door to expose the control 9s Master Board. 2. Clearly label all of the cables, daughter boards and their locations that are connected to the Master Board. Once all the cables and boards are labeled, you can loosen and remove the cables and daughter boards using a screwdriver including the MEM-A3 board (for 0-C and 0- 4PC upgrades). You are now ready to remove the battery connection (CPA7) from the bottom of the Master Board (see cMaster Trick d note blow). Master Trick: With great care, it is possible to install the modules and not have the battery removed. If each module is carefully inserted so as not to short the battery to ground, you may find the main memory has been saved. Worst case is that you will have to do the manual restore listed below. Test this by powering up not holding RESET & DELETE in the beginning. 3. Put on an anti-static wrist strap if available and clip the other end of it to the GND post in the top corner of the Master Board. Locate the SRAM socket positions on the Master Board / MEM-A3 board (see pages 4-5). This is where you have to insert or replace the larger of the new memory modules. Optionally if there are already modules in these locations, you can use the small screwdriver or a chip puller to carefully remove them. Also locate the smaller SRAM parity socket positions on the Master Board (0-A and 0-B upgrades only). This is where the smaller of the new memory modules go. Chapter 3 3 Installation for Fanuc ® 0 M100602D Copyright © Memex Automation Inc. 2004 - 2007 Page 11 of 19 4. One by one, remove the memory module from the kit. Optionally apply a drop of the anti- oxidant Stabilant-22A solution to the pins of the memory module. This will ensure a positive electrical connection between the pins. It will also act like a lubricant during insertion. Check that the pins are straight and be wary of static discharge that may damage the memory modules. 5. Orient the module above the socket with the cnotch d in the same direction as the cnotch d in the socket (Pointing c Down d). Place one row of pins in the socket, then with a little sideways pressure put the second row in. With steady pressure, push the memory module down into the socket. Check that none of the pins have bent in during this process. Repeat this step for the remaining modules. 6. Again, check your work before replacing any daughter boards back in the control. After you replace the daughter boards and restore all of the cable connections, check your work. After you are confident that every cable has been correctly connected, power up the control while holding the MDI keys RESET & DELETE simultaneously. This will erase the new Master Board memory in preparation for your information. 7. Now you are ready to proceed with the reloading of all of your parameters and programs. Chapter 3 3 Installation for Fanuc ® 0 M100602D Copyright © Memex Automation Inc. 2004 - 2007 Page 12 of 19 Restoring your Fanuc ® ®® ® 0 At this time, you should run the Memex upgrade software provided on the diskette included with your manual. It not only checks your NCP file for integrity, but it toggles any bits that need changing. Please contact us if you need help at this point. Place the Memex Upgrade diskette in the A: drive on your computer. Go to the Start menu and click on R un... Type [A:\UPGD0.EXE], then [OK] or at the DOS prompt type [A:], then [Enter] followed by [UPGD0], then [Enter]. After viewing the acknowledgment screen, press F3 to open the .NCP (parameter) file that you received from your control. Press F9 to perform the upgrade on your file. After the software has performed the upgrade successfully, exit the software by pressing Alt-X. I. RESTORING THE SYSTEM PARAMETERS With the Emergency Stop button depressed, set the PWE parameter on page 2 of the SETTINGS screen to a 1. Press DGNOS/PARAM, [PARAM] and page down to parameter 900. Enter the values for parameters 900-1000. At this time, set up the communication parameters again the same way you did in Part 1-CNC Parameter Settings. When you are finished, turn off the power to the control, then power on again. II. READING CNC PARAMETERS (PC - CNC) " Set the PWE parameter, then press DGNOS/PARAM, [PARAM] and set up the CNC communication parameters in accordance with the following. On the SETTINGS (Handy) screen, set the following: TVON = 0 (TV Check off) ISO = 1 (ISO data format) I/O = 0 (port number) PWE = 0 (Parameter Write Enable OFF) TAPE = 0 You should have the original settings written on page 16 (as per page 7) to be restored after all other parameters are restored via the serial port. In order to do this set the parameters for the serial ports as per Chart 1 (page 7) and Chart 2 (page 8). Chapter 3 3 Installation for Fanuc ® 0 M100602D Copyright © Memex Automation Inc. 2004 - 2007 Page 13 of 19 " Set up the communications software on your computer to send a file. " Perform the following steps on the PC and CNC as follows: CNC-- In EDIT mode, press the DGNOS/PARAM, [PARAM], INPUT keys. (The CNC will flash LSK in the lower right corner of the CRT.) PC-- Send the file with the .NCP extension to the control. When the parameters have been received, Power OFF the control, then power it ON again. III. WRITING THE PC PARAMETERS You must manually input into the control, ALL of the Diagnostic parameters between No. 300-600. At the end of this entering what you can, cycle the power completely (that is power off even back to the main breaker - this reset the servo drives by the way). IV. READING CNC TOOL OFFSETS " Set up the CNC parameters in accordance with section 1. " Set up the communications software on your computer to send a file. " Perform the following steps on the PC and CNC as follows: CNC-- In EDIT mode, press the OFFSET, then [INPUT] keys. (The CNC will flash LSK in the lower right corner of the CRT.) PC-- Send the file with the .TOF extension to the control. This should reload all of your tool offsets. CNC-- Execute this .TOF file to set the Tool Offsets. CNC-- Delete this file from the Programs in the CNC. V. READING CNC PART PROGRAMS " Set up the CNC parameters in accordance with section 1. " Set up the communications software on your computer to send a file. " Perform the following steps on the PC and CNC as follows: CNC-- In EDIT mode, with the memory protect KEY switched off, Press the EDIT/AUTO, [PRGRM], then INPUT keys.(The CNC will flash LSK in the lower right corner of the CRT.) PC-- Send the file with the .PGM extension to the control. This should reload all of your programs. Don 9t forget to reset parameter 10 if you had previously changed it. That will protect your macro programs (if applicable). Chapter 3 3 Installation for Fanuc ® 0 M100602D Copyright © Memex Automation Inc. 2004 - 2007 Page 14 of 19 VI. CLEAR ABSOLUTE ENCODER (if applicable) 1. Power up with cNo.QRP d + cCAN d or cP d + cCAN d to clear (or reset) any absolute encoders if applicable. You will know this is needed if the machine over-travels upon homing, but is a long way from normal home. 2. Reference machine manually as usual. Restore any of the NC parameters that you changed from their original state (see SETTING, communications settings etc. You will have to set PWE to do this. Double check the INCH versus METRIC setting in the SETTING HANDY screen (a metric setting which is the default, will make the machine seem to crawl when a program asks for what it thought was an INCH move). Check the MIRROR AXES settings as well. " Also remember to re-protect your 9000 level programs with parameter 10 bit 4 (xxx1 xxxx) if applicable. After a complete test - including exercising the tool changer if applicable - you will have completed your installation. Remember to change the 3 D cell batteries that keep your control memory backed up on a regular basis (once a year) with the CNC control power ON . Call Memex if you would like to investigate our MxBRU Battery Replacement Unit. Fanuc Serial Cable: Pin 1 Frame Ground Pin 4 Request to Send Pin 7 Signal Ground Pin 2 Transmit Data Pin 5 Clear to Send Pin 8 Carrier Detect Pin 3 Receive Data Pin 6 Data Set Ready Pin 20 Data Terminal Ready Normally pins 6, 8 & 20 are jumpered on the Fanuc side. Also pins 2 & 3 are usually crossed, as are 3 & 4, when connected to a PC with a DB25 connector. Note that Fanuc has +24 volts on pin 25! Chapter 4 3 Appendix M100602D Copyright © Memex Automation Inc. 2004 - 2007 Page 15 of 19 Appendix Technical Summary for Fanuc ® 0 PUNCHING Punch NC Parameters - EDIT mode, PARAM screen, EOB + OUTPUT/START Punch PC Parameters - EDIT mode, DGNOS screen, OUTPUT/START Punch All Programs - EDIT mode, PRGRM screen, 0-9999, OUTPUT/START Tool Offsets - EDIT mode, OFFSET screen, OUTPUT/START READING Load NC Parameters - EDIT mode, PARAM screen, EOB + INPUT Load PC Parameters - EDIT mode, DGNOS screen, INPUT Load All Programs - EDIT mode, PRGRM screen, INPUT Load Tool Offsets - EDIT mode, OFSET screen, INPUT CLEARING Delete All memory - Power On holding RESET + DELETE Standard Fanuc ® Serial Port: (DB-25 Female) 1 = Frame Ground 6 = Data Set Ready 2 = Transmit Data 7 = Signal Ground 3 = Receive Data 8 = Carrier Detect 4 = Ready To Send 20= Error (Data Terminal Ready) 5 = Clear To Send 25= +24 Volts The usual software handshaking cable configuration has 2, 3 crossed & 7 connected straight through (with 4&5 jumpered - or used if hardware handshake lines are preferred) and pins 6,8 & 20 jumpered on the control side only. Fanuc ® ISO Protocol: (E,7,x) The standard protocol for Fanuc ® controls is cEven parity d, c7 data bits d and either c1 or 2 stop bits d) See Parameters 101, 111, 121 and 131 above Determination of Fanuc 0 Model Types To determine the version of the Fanuc 0 series CNC Control, check the master board number and/or the software version. The Master board number is found on the top left side of the main circuit board, usually mounted in the control cabinet that has the daughter card attached. It should not be confused with cA02B-????-???? d numbers, which are Fanuc 9s ordering numbers and are usually found on a sticker above the master board. Use the following table to determine which unit you have. You can determine the software version by powering-up the control with E-stop active (button depressed). The control should hang on the software version screen (in the lower right corner of this screen, you will see the servo version number as well). Please note that Memex has a MxBRU (Battery Replacement Unit) available that provides a maintenance-free rechargeable Lithium battery backup for this control. 1985 / 1986 Fanuc 0-MA and Fanuc 0-TA 120M maximum battery backed resident memory. 1987 / 1989 Fanuc 0-MB and Fanuc 0-TB 320M maximum battery backed resident memory. 1990 / 1998 Fanuc 0- MC and Fanuc 0-TC 320M maximum battery backed resident memory. Chapter 4 3 Appendix M100602D Copyright © Memex Automation Inc. 2004 - 2007 Page 16 of 19 Parameter Worksheet Company:_________________________________ Machine No.:___________ Date:_____________ Fanuc ® 0-___ Software Version: _______________ Main CPU Board No.: _____________________ Setting Screen Data TV ON PWE ISO TAPE I/O PC Parameters Par. Value Par. Value Par. Value Par. Value Par. Value Par. = Parameter Number Chapter 4 3 Appendix M100602D Copyright © Memex Automation Inc. 2004 - 2007 Page 17 of 19 Diagnostics Parameters Parameter Data Parameter Data D300 D375 D301 D376 D305 D390 D306 D391 D310 D395 D311 D315 COUNTER 1 D316 D380 D320 D381 D321 D382 D325 D326 COUNTER 2 D330 D385 D331 D387 D335 D340 PC SWITCH D341 D400 D345 D420 D346 D421 D350 D422 D351 D423 D355 D424 D356 D360 DATA TABLE D361 D440 D365 D441 D366 D370 TOOL CHANGE D371 D382 D387 Chapter 4 3 Appendix M100602D Copyright © Memex Automation Inc. 2004 - 2007 Page 18 of 19 Spare Parameter Sheet No. Data No. Data No. Data No. Data. 0 0 0 0 1 1 1 1 2 2 2 2 3 3 3 3 4 4 4 4 5 5 5 5 6 6 6 6 7 7 7 7 8 8 8 8 9 9 9 9 0 0 0 0 1 1 1 1 2 2 2 2 3 3 3 3 4 4 4 4 5 5 5 5 6 6 6 6 7 7 7 7 8 8 8 8 9 9 9 9 0 0 0 0 1 1 1 1 2 2 2 2 3 3 3 3 4 4 4 4 5 5 5 5 6 6 6 6 7 7 7 7 8 8 8 8 9 9 9 9 0 0 0 0 1 1 1 1 2 2 2 2 3 3 3 3 4 4 4 4 5 5 5 5 6 6 6 6 7 7 7 7 8 8 8 8 9 9 9 9 0 0 0 0 1 1 1 1 2 2 2 2 3 3 3 3 4 4 4 4 5 5 5 5 6 6 6 6 7 7 7 7 8 8 8 8 Chapter 4 3 Appendix M100602D Copyright © Memex Automation Inc. 2004 - 2007 Page 19 of 19 Memex Automation Inc. 777 Walkers Line, Burlington, Ontario Canada L7N 2G1 Phone: 905-635-3040 Fax: 905-631-9640 Thank you for using Memex memory

less