Cisco CallManager and IP Phone 7960 Emulation: Configuration and

To view this page ensure that Adobe Flash Player version 9.0.124 or greater is installed.

Please login or register to make a comment!

NetLink e340/i640 Wireless Telephone Cisco CallManager and IP Phone 7960 Emulation Configuration and Administration Part Number: 72-1082-02 Issue G SpectraLink Corporation Configuration and Administration 4NetLink e340/i640 Wireless Telephone Cisco CallManager and IP Phone 7960 Emulation 72-1082-02-G.doc Page 2 Trademark Information Polycom® and the logo designs SpectraLink® LinkPlus Link NetLink SVP Are trademarks and registered trademarks of Polycom, Inc. in the United States of America and various countries. All other trademarks used herein are the property of their respective owners.

Patent Information The accompanying product is protected by one or more US and foreign patents and/or pending patent applications held by Polycom, Inc. Copyright Notice Copyright © 2003 to 2008 Polycom, Inc. All rights reserved under the International and pan-American copyright Conventions.

No part of this manual, or the software described herein, may be reproduced or transmitted in any form or by any means, or translated into another language or format, in whole or in part, without the express written permission of Polycom, Inc. Do not remove (or allow any third party to remove) any product identification, copyright or other notices. Every effort has been made to ensure that the information in this document is accurate.

Polycom, Inc. is not responsible for printing or ... more. less.

clerical errors. Information in this document is subject to change without notice and does not represent a commitment on the part of Polycom, Inc. Notice Polycom, Inc. has prepared this document for use by Polycom personnel and customers. The drawings and specifications contained herein are the property of Polycom and shall be neither reproduced in whole or in part without the prior written approval of Polycom, nor be implied to grant any license to make, use, or sell equipment manufactured in accordance herewith. Polycom reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult Polycom to determine whether any such changes have been made. No representation or other affirmation of fact contained in this document including but not limited to statements regarding capacity, response- time performance, suitability for use, or performance of products described herein shall be deemed to be a warranty by Polycom for any purpose, or give rise to any liability of Polycom whatsoever. Contact Information Please contact your Polycom Authorized Reseller for assistance. Polycom, Inc. 4750 Willow Road, Pleasanton, CA 94588 http://www.polycom.com SpectraLink Corporation Configuration and Administration 4NetLink e340/i640 Wireless Telephone Cisco CallManager and IP Phone 7960 Emulation 72-1082-02-G.doc Page 3 Table of Contents 1. About This Document 4 1.1 Referenced Documents 4 1.2 Customer Support Hotline 4 1.3 Icons and Conventions 4 2. NetLink Wireless Telephone Overview 5 2.1 QoS and Security 5 2.2 Quick Start Guide 6 2.3 System Diagram 7 2.4 System Components 8 3. The NetLink Wireless Telephone 10 3.1 Specifications 10 3.2 The Handset Display 11 3.3 Startup Sequence 13 3.4 Handset Modes 14 3.5 NetLink Wireless Telephone Displays 15 4. NetLink Wireless Telephone Configuration 16 4.1 The Admin Menu 16 4.2 User-defined Preferences 24 5. License Management 30 5.1 Requirements 30 5.2 Configuration Process 30 6. CallManager Integration Factors 32 7. Feature Programming 34 7.1 Feature Assignment 35 7.2 Feature Access 36 8. Testing a Handset 39 9. Diagnostic Tools 40 9.1 Run Site Survey 40 9.2 Diagnostics Mode 42 9.3 Syslog Mode 45 10. Certifying the NetLink Wireless Telephones 47 10.1 Conducting a Site Survey 47 11. Software Maintenance 48 11.1 Upgrading NetLink Wireless Telephones 48 12. Troubleshooting NetLink Wireless Telephone Problems 50 12.1 Access Point Problems 50 12.2 Configuration Problems 50 12.3 NetLink Wireless Telephone Status Messages 51 SpectraLink Corporation Configuration and Administration 4NetLink e340/i640 Wireless Telephone Cisco CallManager and IP Phone 7960 Emulation 72-1082-02-G.doc Page 4 1. About This Document This document explains how to configure and maintain the NetLink e340/i640 Wireless Telephone within Cisco IP telephony systems that employ CallManager, CallManager ITS, CallManager SRST, versions 3.x and 4.1; and CCME (Call Manager Express) version 3.2. The instructions in this document are for SpectraLink Software Version: 91.040 and higher. 1.1 Referenced Documents SpectraLink 8000 SVP Server: Administration Guide for Mitel and Cisco (1725-36031-001) Available at http://www.polycom.com/usa/en/support/voice/wi- fi/spectralink_8000_svp_server.html Polycom WLAN Compatibility Table (1725-36040-001) Access Point Configuration Guide (1725-36xxx-001 where xxx indicates a number corresponding to the type of access point.) Available at http://www.polycom.com/usa/en/support/voice/wi- fi/wi_fi_interoperability.html Deploying Enterprise-Grade Wi-Fi Telephony white paper. Available at http://www.polycom.com/common/documents/products/voice/mobile/bestpracti ces_SLNK_032708.pdf Open Application Interface (OAI) Specification (72-0052-00) Available by request from SpectraLink Customer Service. 1.2 Customer Support Hotline SpectraLink wants you to have a successful installation. If you have questions please contact the Customer Support Hotline at (800) 775-5330. The hotline is open Monday through Friday, 6 a.m. to 6 p.m. Mountain time. For Technical Support: technicalsupport@polycom.com For Knowledge Base: http://www.polycom.com/usa/en/support/voice/voice.html 1.3 Icons and Conventions This manual uses the following icons and conventions. Caution! Follow these instructions carefully to avoid danger. Note these instructions carefully. NORM This typeface indicates a key, label, or button on the NetLink Wireless Telephone. SpectraLink Corporation Configuration and Administration 4NetLink e340/i640 Wireless Telephone Cisco CallManager and IP Phone 7960 Emulation 72-1082-02-G.doc Page 5 2. NetLink Wireless Telephone Overview The NetLink e340/i640 Wireless Telephone is a mobile handset for workplace IP telephone systems. The handset operates over an 802.11b wireless Ethernet LAN providing users a wireless voice over IP (VoIP) extension. By seamlessly integrating with the Cisco CallManager, handset users are provided with high-quality mobile voice communications throughout the workplace. The handset gives users the freedom to roam throughout the workplace while providing all the features and functionality of an IP desk phone. The NetLink e340/i640 Wireless Telephone provides a wireless extension to Cisco CallManager v3.08 and later. The NetLink e340/i640 Wireless Telephone supports the Skinny Client Control Protocol (SCCP). cSkinny d is an open protocol developed by Cisco Systems for communication between an IP phone and the CallManager call processing application. The handset can also be registered to other platforms supporting SCCP, such as CallManager Express (CME) and Cisco SRST. The handsets reside on the wireless LAN with other wireless devices using Direct Sequence Spread Spectrum (DSSS) radio technology. The handset radio transmits and receives packets at up to 11Mb/s. A CallManager template for the handset must be configured for the specific features and lines to be accessed by the handset. The handset can be automatically added to the network and registered with CallManager, or each of these steps can be configured manually. After the handset is registered it receives its configuration information from CallManager. 2.1 QoS and Security The NetLink SVP Server is an Ethernet LAN device that works with the access points (APs) to provide QoS on the wireless LAN. Voice packets to and from the NetLink Wireless Telephones are intercepted by the NetLink SVP Server and encapsulated for prioritization as they are routed to and from an IP telephony server or gateway. See the SpectraLink 8000 SVP Server: Administration Guide for Mitel and Cisco document for detailed information about this device. The NetLink e340/i640 Wireless Telephone supports Wired Equivalent Privacy (WEP) as defined by the 802.11 specification. SpectraLink offers the product with both 40-bit and 128-bit encryption. NetLink Wireless Telephones support basic WMM" (Wi-Fi Multimedia) if also supported by the AP as part of the 802.11e protocol. If the AP supports WMM, the handset automatically discovers and uses it. WMM does not replace the NetLink SVP Server as described in the following paragraph. WMM settings must be configured on the SVP Server. NetLink Wireless Telephones also support the 802.11i protocol including Wi-Fi Protected Access (WPA" and WPA2") 4PSK. As vendors introduce APs that are eligible to become Wi-Fi CERTIFIED" for WPA-PSK and/or WPA2-PSK, SpectraLink will determine their compatibility with the NetLink Wireless Telephones and include them on the Polycom WLAN Compatibility Table . SpectraLink Corporation Configuration and Administration 4NetLink e340/i640 Wireless Telephone Cisco CallManager and IP Phone 7960 Emulation 72-1082-02-G.doc Page 6 The latest software versions are required to support the features described in this document. 2.2 Quick Start Guide 1. A wireless LAN must be properly configured and operational through the use of 802.11b wireless APs. 2. A TFTP server must be available on the network in order to load the appropriate software into the handsets. Most installations choose to take advantage of the TFTP server that accompanies the CallManager, making a separate TFTP server unnecessary. See Section 5 License Management for detailed instructions for loading software on handsets. 3. Cisco 9s CallManager (Release 3.08 or greater) must be connected to your network and completely operational. 4. The NetLink SVP Server, which facilitates the QoS on the wireless LAN for the handsets, must be on the same subnet as the handsets and have the proper versions of software. 5. Visit http://www.polycom.com/usa/en/support/voice/wi-fi/wi-fi.html to download the latest NetLink Wireless Telephone and SVP Server software. 6. Download software: Download the correct NetLink Wireless Telephone software per Section 4.2 Configuration Process . Ensure the software is properly loaded on the TFTP server. 7. Download updates to the NetLink SVP Server software per SpectraLink 8000 SVP Server: Administration Guide for SRP Chapter 5, section on Software Updates . 8. Configure your handset to ensure that it associated with the Wireless LAN, has the appropriate software and is registered to CallManager. See Section 5 License Management for detailed instructions for loading software onto handsets. IP multicast addresses are used by the NetLink i640 Wireless Telephone system. This requires that multicasting be enabled on the subnet used for the NetLink Wireless Telephones and SVP Server. Routers are typically configured with filters to prevent multicast traffic from flowing outside of specific domains. The wireless LAN can be placed on a separate VLAN or subnet to reduce the effects of broadcast and multicast traffic from devices in other network segments. SpectraLink Corporation Configuration and Administration 4NetLink e340/i640 Wireless Telephone Cisco CallManager and IP Phone 7960 Emulation 72-1082-02-G.doc Page 7 2.3 System Diagram The following diagram shows the SpectraLink components residing on a network with Cisco CallManager, APs, and wireless LAN Ethernet Switched Hub: Ethernet switch A ccess Poin t Wireless POS handsets A ccess Poin t Cisco CallManager Cisco IP Phones optional Cisco Voice Gateway PSTN or PBX Device supplied by SpectraLink Ethernet cable Phone cable NetLink SVP Server(s) Optional multiple SVP Servers SpectraLink Corporation Configuration and Administration 4NetLink e340/i640 Wireless Telephone Cisco CallManager and IP Phone 7960 Emulation 72-1082-02-G.doc Page 8 2.4 System Components NetLink e340 Wireless Telephone The NetLink e340 Wireless Telephone is a lightweight, durable handset specifically designed for mobile workplace use within a facility using the Cisco CallManager and 802.11b APs in a wireless LAN. NetLink i640 Wireless Telephone The NetLink i640 Wireless Telephone offers a durable design with push-to-talk functionality. Handset functionality is provided by emulating the Cisco IP Phone 7960. Using SCCP, the handset supports the 6 line/speed-dial buttons and softkeys. Among other features, the handset can receive calls directly, receive transferred calls, transfer calls to other extensions, initiate conference calls, and make outside and long distance calls (subject to the restrictions applied in your facility.) The handsets are to be used on-premises; they are not cellular or satellite phones. NetLink e340/i640 Wireless Telephones use Direct Sequence Spread Spectrum radio technology (DSSS) to transmit audio packets over wireless LAN APs that support SpectraLink Voice Priority (SVP). NetLink SVP Server SpectraLink Voice Priority (SVP) is the SpectraLink quality of service (QoS) mechanism that is implemented in the handset and AP to enhance voice quality over the wireless network. SVP gives preference to voice packets over data packets on the wireless medium, increasing the probability that all voice packets are transmitted efficiently and with minimum or no delay. SVP is fully compatible with the IEEE 802.11b standards. The NetLink SVP Server is an Ethernet LAN appliance that works with the AP to provide QoS on the wireless LAN. All SCCP packets to and from the NetLink e340/i640 Wireless Telephones pass through the NetLink SVP Server and are encapsulated for prioritization as they are routed to and from the CallManager or other telephone. CallManager The software-based call-processing component of the Cisco IP telephony solution. Access points (APs) are supplied by third party vendors and provide the connection between the wired Ethernet LAN and the wireless (802.11b) LAN. APs must be positioned in all areas where NetLink Wireless Telephones will be used. The number and placement of APs will affect the coverage area and capacity of the wireless system. Typically, the requirements for use of NetLink e340/i640 Wireless Telephones are similar to that of wireless data devices. APs must utilize SpectraLink Voice Priority (SVP). Contact SpectraLink, or a certified SpectraLink distributor, for information about APs that support SVP. Ethernet switch Interconnects multiple network devices, including the NetLink SVP Server, the CallManager, Cisco IP Phones and the APs. Ethernet switches provide the highest performance networks, which can handle combined voice and data traffic, and are required when using the NetLink e340/i640 Wireless Telephones. Although a single Ethernet switch network is recommended, the handsets and the NetLink SVP Server can operate in larger, more complex networks, including SpectraLink Corporation Configuration and Administration 4NetLink e340/i640 Wireless Telephone Cisco CallManager and IP Phone 7960 Emulation 72-1082-02-G.doc Page 9 networks with multiple Ethernet switches, routers, VLANs, and/or multiple subnets, as long as the SVP Server and APs are on the same subnet. However, in such networks, it is possible for the QoS features of the NetLink SVP Server to be compromised, and voice quality may suffer. Any network that consists of more than a single Ethernet switch should be thoroughly tested to ensure any quality issues are detected. Note that the NetLink e340/i640 Wireless Telephones cannot actively roam from one subnet to another. If routers and multiple subnets are in use, the NetLink Wireless Telephones must only use APs attached to a single subnet, or be powered off and back on to switch to a different subnet. Cisco IP Phone The wired LAN desksets provided by Cisco for use with the CallManager. Cisco Voice Gateway A wired-LAN component that provides access to telephony resources outside the CallManager and the IP Network. Voice Gateways can connect to the Public Telephone Network or to certain PBXs. Contact Cisco for more information about available Voice Gateways. TFTP server Required in the system to distribute software to the handsets. May be on a different subnet than the CallManager and APs. SpectraLink Corporation Configuration and Administration 4NetLink e340/i640 Wireless Telephone Cisco CallManager and IP Phone 7960 Emulation 72-1082-02-G.doc Page 10 3. The NetLink Wireless Telephone NetLink e340 Wireless Telephone NetLink i640 Wireless Telephone 3.1 Specifications Radio frequency: 2.4000 3 2.4835 GHz Transmission type: Direct Sequence Spread Spectrum (DSSS) Transmit data rate: Up to 11 Mb/s Radio QoS: SpectraLink Voice Priority (SVP), WMM Wireless security: Wired Equivalent Privacy (WEP), 40-bit and 128-bit, Cisco FSR; WPA-PSK, WPA2-PSK FCC certification: Part 15.247 Management: DHCP, TFTP Voice encoding: G.711 (A- and mu-law), G.729a/ab VoIP Protocols: Skinny Client control Protocol (SCCP) Transmit power: 100 mW peak, < 10 mW average (US/NA) Display: Pixel-based (up to 4-line x 18-character) alphanumeric, plus line and status indicators. e340 dimensions: 5.5 d x 2.0 d x 0.9 d (14.0 x 5.1 x 2.3 cm) i640 dimensions: 5.9 d x 2.2 d x 1.0 d (15.0 x 5.6 x 2.5 cm) e340 weight: 4.2 ounces (119.0 g) i640 weight: 6.0 ounces (170.1 g) Battery capacity: 4 hours talk time, 80 hours standby (30 hours standby if push to talk (PTT) is enabled) SpectraLink Corporation Configuration and Administration 4NetLink e340/i640 Wireless Telephone Cisco CallManager and IP Phone 7960 Emulation 72-1082-02-G.doc Page 11 3.2 The Handset Display Icons The top row of the handset display in the Cisco SCCP implementation is customized to provide four line appearances with two calls on each. The top row icons and their positions are shown below: Signal strength The signal strength icon indicates the strength of the signal from the AP and can assist the user in determining if the handset is moving out of range. It is always present on the display in the upper left corner. Line indicators The four line numbers indicate activity on each of the four possible line appearances. The first tab indicates the active line and the second tab indicates its status. Voicemail The voicemail icon is activated when a new voicemail message is received if the feature is supported by the phone emulation. It appears to the right of the signal strength icon. Download The download icon indicates that the handset is downloading code. This icon only appears while the handset is running the over-the-air downloader. It appears in the same location as the voicemail icon. Call status The call status icons indicate the type of activity occurring on the first and second call on the tabbed line. Navigation arrows The navigation arrow icons indicate up and down or left and right scrolling options. Scroll through the display by pressing the Up and Down buttons on the left side of the handset. Signal strength icon Line numbers Voicemail indicator Call one status Call two status Navigation arrows Battery icon Tab Tab SpectraLink Corporation Configuration and Administration 4NetLink e340/i640 Wireless Telephone Cisco CallManager and IP Phone 7960 Emulation 72-1082-02-G.doc Page 12 Battery charge The battery icon indicates the amount of charge remaining in the Battery Pack. There are three levels and when only one level remains, the Battery Pack needs to be charged. It is always present on the display in the upper right corner. Alphanumeric text The NetLink e340/i640 Wireless Telephone supports a two to four line display of up to 19 alphanumeric characters. Display information provided by the Cisco CallManager when the handset is off-hook will be passed directly to the handset display. The handset will display only the first 16 characters of each line. Certain characters may be used by the Cisco CallManager that are not implemented in the handset such as definable and special characters. See the Feature Programming section for an explanation of displayed features. Press the FCN key while off hook to scroll through features and emulated keys. Press the LINE key while off hook to scroll through the line/memory keys. Softkey display area When the handset is active, the bottom row displays up to four softkey feature abbreviations. The full text may be viewed by pressing the MENU key. Press the corresponding softkey to activate the feature. Ringing and tones The ringing types are programmed by the handset user into the handset and are not accessible or changeable by the CallManager. When Ring Cadence is set to PBX and whenever possible, the audible and vibrating ringer on the handset will follow the SCCP protocol cadence commands provided by the Cisco CallManager. See the User Preferences section. Audio features The Cisco IP Phone 7960 speakerphone features are not available on the handset. SpectraLink Corporation Configuration and Administration 4NetLink e340/i640 Wireless Telephone Cisco CallManager and IP Phone 7960 Emulation 72-1082-02-G.doc Page 13 3.3 Startup Sequence The handset goes through an initialization sequence at startup. The line icons 1-9 display and count down as the handset steps through this sequence. This is usually very rapid. If there is any difficulty at any step that prevents initialization from continuing, an error message will display and the related icon(s) will stay on. Please see the error table at the back of this document for instructions on how to handle error messages that occur during initialization. Icon The icon(s) shown in bold turns off when: 123456789 The handset has located and authenticated and associated with at least one AP, and is proceeding to bring up higher-layer networking functions. 12345678 The handset is either configured for Static IP, or if configured for DHCP the DHCP discovery process has started. 1234567 If DHCP is configured, a DHCP response was received which contains a good DNS server configuration. 123456 Note: Only valid on non-SRP protocol. Indicates one of the following: Static IP configuration, or SVP Server address found in DHCP response, or SVP Server address found via DNS lookup. 12345 All networking functions are complete (notably, DHCP) and the handset is proceeding with establishing the SRP link to the SVP Server. 1234 The SRP link is established, all network stack initialization is complete, proceeding with application- specific initialization. 123 The link between the handset and the TFTP server is established. The handset displays Trying TFTP [n] . [n] is the retry count. 12 The handset has opened a connection to the CallManager. The handset displays Opening . 1 The handset has registered to the CallManager. The handset displays Registering [n] . [n] is the progress down counter while performing the registration. The start number depends on the CallManager version. (no icons) EXT. XXXXX Initialization is complete. The handset is in standby mode ready to receive and place calls. SpectraLink Corporation Configuration and Administration 4NetLink e340/i640 Wireless Telephone Cisco CallManager and IP Phone 7960 Emulation 72-1082-02-G.doc Page 14 3.4 Handset Modes Standby (on-hook) In the standby mode the handset is waiting for an incoming call or for the user to place an outgoing call. The extension number is shown on the display and there is no dial tone. In this mode, the handset is conserving battery power and wireless LAN bandwidth. When an incoming call occurs the handset will ring until the call is answered by pressing the Start Call key or the End Call key is pressed to silence the ringing. Active (on hook) Press the MENU key in standby mode to emulate the on-hook state of the IP Phone 7960. Active (off-hook) predial To place a call using predialing (cell phone dialing), dial the number while in standby mode and then press Start Call . This transitions the handset to active off-hook mode and the number is immediately called. Active (off hook) To place a call, press the Start Call key. This transitions the handset to active off- hook mode. There is a dial tone, the handset is in communication with the PBX, and the display shows information as it is received from the PBX. The user may place a call or press the FCN , MENU or LINE key to access operations. The handset is also in the active mode when a call is received. When an incoming call occurs during an active call the handset will play the second line ringing sound until the call is answered, the caller hangs up, or the call transfers to voicemail. If End Call is pressed, the first call is terminated and the handset reverts to a full ring. The active modes utilize the most bandwidth and battery power. To conserve these resources, return the handset to the standby mode when a call is completed by pressing the End Call key. SpectraLink Corporation Configuration and Administration 4NetLink e340/i640 Wireless Telephone Cisco CallManager and IP Phone 7960 Emulation 72-1082-02-G.doc Page 15 3.5 NetLink Wireless Telephone Displays Status display area When active, the handset displays a row of line icons at the top of the screen. There are four rows available for text display and a bottom row that displays softkey abbreviations. Information from the PBX is shown on the text row above the softkeys. Note that PBX text that would normally be displayed on the Cisco IP Phone 7960 may be truncated to 16 to 19 characters on the handset. <Muted> is displayed on the second text row when local muting is activated. LINE display Pressing the LINE key from the active mode displays a list of line appearances extracted from the programmable keys list. The line appearances are also mapped to corresponding line icons. MENU display Pressing the MENU key from the active state displays an expanded description of the softkey features. If configured, pressing MENU in an active state will display the diagnostic menus. Pressing the MENU key from the standby state takes you into active on-hook mode. FCN display Pressing the FCN key from the active mode displays the Mute, Voicemail, OAI functions and the speed dial list. SpectraLink Corporation Configuration and Administration 4NetLink e340/i640 Wireless Telephone Cisco CallManager and IP Phone 7960 Emulation 72-1082-02-G.doc Page 16 4. NetLink Wireless Telephone Configuration Each handset may be configured for site-specific requirements by opening the Admin menu and selecting options or entering specific information. Any settings entered in the Admin menu must conform to system settings. Only the handset being configured is affected by the Admin menu settings. The NetLink e340/i640 Wireless Telephones can be automatically registered at first turn on. The handset can be automatically configured for IP Address, ESSID and/or CallManager by enabling DHCP, ESSID Learning, and automatic registration (at CallManager), respectively. The handset user may select several usability options from the Standby menu, described below in the User-defined Preferences section. This information is also provided in the end-user manual. The NetLink Configuration Cradle is an accessory device designed to automate configuration of e340 and i640 models of the NetLink Wireless Telephone. The Configuration Cradle is connected to a PC via a serial cable. A downloadable Configuration Cradle program runs on the PC and enables the system administrator to establish and store configuration options for system, group and user levels. A configuration plan may be set up in the program and downloaded into a handset or a configured handset may be placed in the cradle and its configuration may be uploaded and edited or saved. Please see your service representative or contact SpectraLink Customer Service for more information about this time-saving device 4.1 The Admin Menu The Admin menu contains configuration options that are stored locally (on each handset). Every handset is independent; if the default settings are not desired, the Admin options must be set in each handset requiring different settings. Opening the Admin menu 1. With the handset powered OFF, simultaneously press and hold the Power On and Power Off keys. 2. Release the Power On key, wait for a single beep, then release the Power Off key. The Admin menu displays. If an Admin password has been set, the display will require its entry before opening the Admin menu. If no password is set, the display will proceed directly into the Admin menu. SpectraLink Corporation Configuration and Administration 4NetLink e340/i640 Wireless Telephone Cisco CallManager and IP Phone 7960 Emulation 72-1082-02-G.doc Page 17 Entering and editing Admin menu options An asterisk (*) next to an option indicates that it is selected. Use the Up , Down , and Select side buttons and the softkeys to navigate and select: Up/Down buttons: Display previous/next menu item. Select button: Selects the menu item or option. OK softkey Selects the menu item or option. Save softkey: Saves the entry. Bksp softkey: Backspaces to allow editing of entry. Cncl softkey: Cancels edit and returns to previous menu level. Up softkey: Returns to previous menu level. Exit softkey: Exits the menu (at the top level). End Call key: Exits to standby state (from any level) Alphanumeric string entry 1. Press the first digit/letter. The digit displays. Press the key again to scroll through the letters associated with that key. Example: if you press 2 repeatedly, you will see 2, A, B, and C, a, b, and c. The following table shows which key will allow you to enter non-numeric characters or other characters not represented on the keypad. To Enter Press . - _ ! # $ % & 8 ( ) * + , : ; / \ = @ ~ 1 Space 0 Q,q 7 Z,z 9 2. When the correct entry displays, press the Right Arrow key to move on to the next character. Repeat for each digit/letter of the entry. To erase, press the Left Arrow key or Bksp softkey to erase the previous character. 3. Press the Save softkey to save the entry and return to the menu. Press the Cncl softkey to abort and return to the menu without saving any changes. The following table lists the Admin menu items. The default settings are shown in the table below with an * prior to the option. Detailed descriptions of each item appear below the table. SpectraLink Corporation Configuration and Administration 4NetLink e340/i640 Wireless Telephone Cisco CallManager and IP Phone 7960 Emulation 72-1082-02-G.doc Page 18 Admin menu Admin Menu Items 2 nd Level 3 rd Level 4 th Level 5 th Level Phone Config License Option Set Current [List per download] Push-to-talk Allowed Channels *Channel 1 *Channel 2 *Channel 3 *Channel 4 *Channel 5 *Channel 6 *Channel 7 *Channel 8 Allow/Disallow *Allow PTT Disallow PTT Admin Password Enter PW Re-enter Password Network Config IP Addresses *Use DHCP Static IP Phone IP Default Gateway Subnet Mask Syslog Server IP Cisco TFTP Server IP SVP Server IP OAI Server IP ESS ID *Learn Once Learn Always Static Entry Security *None WEP Authentication Open System Shared Key WEP On/Off Key Information Default Key Key Length Key 1-4 Rotation Secret Cisco FSR Username Password WPA-PSK Passphrase Direct Entry WPA2-PSK Passphrase Direct Entry Reg. Domain: xx Transmit Power *Maximum 50 mW 30 mW 20 mW 15 mW 10 mW 5 mW OAI on/off Enable OAI Disable OAI SpectraLink Corporation Configuration and Administration 4NetLink e340/i640 Wireless Telephone Cisco CallManager and IP Phone 7960 Emulation 72-1082-02-G.doc Page 19 Admin Menu Items 2 nd Level 3 rd Level 4 th Level 5 th Level Diagnostics Run Site Survey Diagnostics Mode Diagnostics On *Diagnostics Off Syslog Mode *Disabled Errors Events Full Restore Defaults * default setting 50 mW and 30 mW only appear if Regulatory Domain is set to None or 01. Phone Config License Option License Option lets you select the VoIP protocol that your site is licensed to download and run. The SCCP protocol to use for the handsets is 008 . Any other protocol will cause the handset to malfunction. Push-to-talk All eight push-to-talk channels are allowed by default. To toggle the allowed status of any channel, select Allowed Channels , scroll to the channel to be disallowed and press the Select side button. Allowed channels are displayed with an * in the left column. Only those channels allowed in the Admin menu will appear on the Standby menu where they can be enabled or disabled by the end user. To disallow push-to- talk entirely, select Allow/Disallow , scroll to and select Disallow PTT . Admin Password The Admin Password controls access to the administration functions in the Admin menu. The password must be set in each handset for which controlled access is desired. Handsets are shipped without any Admin menu password. Data entry for the password uses the alphanumeric string entry technique. Type the password and press the Save softkey. A confirmation prompt will appear. Type the password again and press the Save softkey. If the passwords match, the Admin password has been set. If you Save with no entry, the password is erased and the display will not require it before displaying the Admin menu. Network Config IP Addresses There are two modes in which the handset can operate: DHCP enabled or Static IP. Select the mode from the IP address menu: SpectraLink Corporation Configuration and Administration 4NetLink e340/i640 Wireless Telephone Cisco CallManager and IP Phone 7960 Emulation 72-1082-02-G.doc Page 20 * Use DHCP Will use Dynamic Host Configuration Protocol to assign an IP address each time the handset is turned on. If DHCP is enabled, the handset also receives all other IP address configurations from the DHCP server. Static IP Allows you to manually set a fixed IP address. If selected, the handset will prompt for the IP addresses of each configurable network component. When entering addresses, enter the digits only, including leading zeroes. No periods are required. Regardless of the mode in which the handset is operating, the following components must be configured in the system: Phone IP The IP address of the handset. This is automatically assigned if DHCP is used. If using Static IP configuration, you must obtain a unique IP address for each phone from your network administrator. Default Gateway and Subnet Mask Used to identify subnets, when using a complex network which includes routers. Both of these must be configured either with an IP address under Static IP (not set to 000.000.000.000 or 255.255.255.255) or with DHCP for the handset to contact any network components on a different subnet. If configured on the DHCP server, use option 3 for the Default Gateway and option 1 for the Subnet Mask. Contact your network administrator for the proper settings for your network. Note that the handsets cannot croam d across subnets, since they cannot change their IP address while operational. Ensure that all your APs are attached to the same subnet for proper operation. The handset can change subnets if DHCP is enabled and the handset is powered off then back on when within range of APs on the new subnet. SpectraLink Corporation Configuration and Administration 4NetLink e340/i640 Wireless Telephone Cisco CallManager and IP Phone 7960 Emulation 72-1082-02-G.doc Page 21 Syslog Server IP The IP address of the syslog server. See the Diagnostics section for more information. Cisco TFTP Server IP The IP address of the TFTP server which holds the CallManager-created configuration files. If using Static IP configuration, this is simply the IP Address of the appropriate TFTP server (often this is the CallManager system). Note that the TFTP server must be statically configured to have a permanent IP Address. If DHCP is being used, the handset will try the following, in order: DHCP option 150 (Cisco TFTP server), then 66 (TFTP server), then a DNS lookup of cCISCOCM1 d if the DHCP options 6 (DNS server) and 15 (Domain Name) are configured. SVP Server IP The IP address of the NetLink SVP Server. If using Static IP configuration, this is simply the IP address of the NetLink SVP Server. Note that the NetLink SVP Server must be statically configured to have a permanent IP address. If DHCP is being used, the handset will try the following, in order: the DHCP option 151, then a DNS lookup of cSLNKSVP2 d if the DHCP options 6 (DNS server) and 15 (Domain Name) are configured. OAI Server IP The IP address of the SpectraLink OAI Gateway (if applicable). If using Static IP configuration, this is simply the IP address of the SpectraLink OAI Gateway. If DHCP is being used, the handset will try the DHCP option 152. ESSID Select the option that will enable the handset to acquire APs with the correct ESSID (Extended Service Set ID, aka SSID) each time it is turned on. Note about Automatic Learn options: Broadcast ESSID must be enabled in the APs for ESSID learning to function. Refer to the Configuration Guide for your AP or call your AP vendor for specifics. Overlapping wireless systems complicate the use of ESSID learning as the handset in an overlapping area could receive conflicting signals. If this is the situation at your site, use Static Entry or Learn Once in an area without overlapping ESSIDs. * Learn Once Allows the handset to scan all ESSIDs for a DHCP server and/or TFTP server. Once either is found, the handset retains the ESSID from whichever AP it associates with at that point. When overlapping wireless systems exist, the Learn Once feature allows the handset to use only the ESSID established at first learn at all subsequent power ons. This ESSID is retained by the handset until the ESSID option is reselected. Learn Always Allows the handset to automatically learn the ESSID at each power on or loss of contact with the wireless LAN (out of range). This may be useful if the handset will be used at more than one site. Static Entry If your APs do not accept broadcast ESSID or if there are overlapping wireless systems in use at the site, enter the correct ESSID manually. Security Security * NONE disables any 802.11 encryption or security authentication mechanisms. SpectraLink Corporation Configuration and Administration 4NetLink e340/i640 Wireless Telephone Cisco CallManager and IP Phone 7960 Emulation 72-1082-02-G.doc Page 22 For WEP, WPA-PSK and WPA2 PSK set each of the following options to match exactly the settings in your APs. Encryption codes display as they are entered. For security reasons codes will not display when a user returns to the Admin menu, Encryption options. WEP (Wired Equivalent Privacy) is a wireless encryption protocol that encrypts data frames on the wireless medium allowing for greater security in the wireless network. If WEP is required at this site, you must configure each handset to correspond with the encryption protocol set up in the APs. Select the entries from the options below to enable the handset to acquire the system. Authentication Select either Open System or Shared Key . WEP On/Off Select either WEP Off or WEP On . Key Information Default Key Enter the key # specified for use by the handsets. This will be 1 through 4 . Key Length Select either 40 - bit or 128 - bit depending on the key length specified for use at this location. Key 1-4 Scroll to the key option that corresponds to the Default Key that was entered above. Enter the encryption key as a sequence of hexadecimal characters. (Use the 2 and 3 keys to access hexadecimal digits A-F, use the Right Arrow key to advance to the next digit, and the Left Arrow key to backspace.) For 40-bit keys you will need to enter 10 digits, for 128-bit keys you will need to enter 26 digits. The display will scroll as needed. Rotation Secret This is used for proprietary WEP key rotation. Refer to your custom document if this feature is supported in your system. Cisco FSR (Fast Secure Roaming) In order to provide the highest level of security without compromising voice quality on Cisco Aironet wireless LAN APs, SpectraLink and Cisco Systems have cooperated to implement the Fast Secure Roaming mechanism. FSR is designed to minimize call interruptions for NetLink handset users as they roam throughout a facility. Existing Aironet 350, 1100, and 1200 APs may require a firmware upgrade to support FSR. Cisco FSR requires advanced configuration of the Cisco APs in your site. See your Cisco representative for detailed documentation on configuring your APs and other required security services on your wired network. To configure Cisco FSR in your NetLink Wireless Telephone, you must enter a Radius Server username and password into each handset. SpectraLink Corporation Configuration and Administration 4NetLink e340/i640 Wireless Telephone Cisco CallManager and IP Phone 7960 Emulation 72-1082-02-G.doc Page 23 Username Enter a username that matches an entry on your Radius server. Usernames are alphanumeric strings, and can be entered using the alphanumeric string entry technique. Password Enter the password that corresponds to this Username. WPA-PSK The security features of WPA (Wi-Fi Protected Access) using PSK (Pre- Shared Key) are available and may be used if supported by the APs in the facility. Select either Passphrase and enter a passphrase between eight and 63 characters in length or Direct Entry and enter the 256-bit key code. WPA2-PSK The security features of WPA2 (Wi-Fi Protected Access) using PSK (Pre-Shared Key) are available and may be used if supported by the APs in the facility. Select either Passphrase and enter a passphrase between eight and 63 characters in length or Direct Entry and enter the 256-bit key code. Consult the Configuration Guide for the APs installed in your facility for information on which of the WPA versions are recommended by SpectraLink engineering. Configure the recommended version on the AP and select the corresponding option on the Admin menu. Regulatory Domain The Regulatory Domain will default to North America on the handset display. FCC requirements dictate that the menu for changing the domain be available by password, which in our case is the LINE key. To change the domain, press LINE and then enter the digits that represent the site 9s domain. Note that both digits must be entered. 01 - North America 02 - Europe (except Spain and France); Japan (channels 1-13) 04 - Spain 05 3 France As of this writing, Spain and France are adopting the general European Regulatory rules. Check with your wireless LAN administrator or supplier for which domain to enter in these countries. Transmit Power Available transmit power is regulated by domain. The Regulatory Domain setting above affects the options available for this setting. The default setting is Maximum which in North America is 100 mW. The Maximum in other domains is 30 mW. Transmit Power may be set to a lower number if necessary by selecting one of the other levels. If changed from the default, ensure the Transmit Power setting is the same on all handsets and all APs. OAI On/Off SpectraLink 9s Open Application Interface (OAI) enables third-party computer applications to display alphanumeric messages on the handset display and take input from the handset keypad. Refer to the Open Application Interface (OAI) Specification documentation for information about administering the OAI Gateway and the services it can provide. SpectraLink Corporation Configuration and Administration 4NetLink e340/i640 Wireless Telephone Cisco CallManager and IP Phone 7960 Emulation 72-1082-02-G.doc Page 24 If you have an OAI Gateway installed in your system, OAI may be optionally enabled in each handset. You may select whether the handset should attempt to connect to the SpectraLink OAI Gateway by choosing either the Enable or Disable options in this menu. If OAI is enabled, and an OAI IP address is available to the handset (either via DHCP or Static IP configuration), the handset will communicate with the OAI Server at power on, and periodically while it is powered on. If you don 9t have a SpectraLink OAI Gateway installed at your site, you should disable the OAI feature to preserve network bandwidth and battery life. Diagnostics Run Site Survey The Site Survey mode is activated by selecting this option. Site survey starts running immediately upon selecting this option. See the Diagnostic Tools section for more information about Site Survey. Diagnostics Mode See the Diagnostic Tools section for a detailed explanation of the Diagnostics Mode options. Syslog Mode See the Diagnostic Tools section for a detailed explanation of the Syslog Mode options. Restore Defaults The Restore Defaults option will set all user and administrative parameters except License Options to their factory defaults. 4.2 User-defined Preferences The following user-defined preferences are also covered in the NetLink e340/i640 Wireless Telephone user guide. The system administrator can refer to this list for more information about customizing handset settings. To configure the following options, the handset must acquire the system (no error message may display) and be at the extension display. This is the standby state. While in the standby state, press and hold FCN briefly to open the user options menu. Use the following keys to display and select options: Up/Down buttons: Display previous/next menu item. Select button: Selects the menu item or option. OK softkey: Selects the menu item or option. Save softkey: Saves the entry. Bksp softkey: Backspaces to allow editing of entry. Cncl softkey: Cancels edit and return to previous menu level. Up softkey: Returns to previous menu level. Exit softkey: Exits the menu (at the top level). End Call key: Exits to standby state (from any level). SpectraLink Corporation Configuration and Administration 4NetLink e340/i640 Wireless Telephone Cisco CallManager and IP Phone 7960 Emulation 72-1082-02-G.doc Page 25 Standby menu Standby menu item 2 nd Level 3 rd Level 4 th Level Lock Keys Language [List per download] Ring Options Telephone Ring Ring Cadence Off *PBX Continuous Short Pulse Long Pulse Ring Tone *Tone 1 Tone 2 Tone 3 Tone 4 Tone 5 Ring Volume+ Bars Vibrate Cadence *Off PBX Continuous Short Pulse Long Pulse Ring Delay** *No Delay 5 Second Delay 10 Second Delay Auxiliary Ring 1 Auxiliary Ring 2 Phone Options Noise Mode *Normal High Severe Key Tones *Enable Tones Disable Tones Warning Tones *Enable warnings Disable warnings Display Contrast Contrast % Keypad Autolock *Disable 5 seconds 10 seconds 20 seconds System Info Phone IP Addr Firmware Version Extension ID Name CallManager IP Addr Push-to-talk Channel Current Channel: X 1 2 3 4 5 6 7 8 New Channel = ? Enable/Disable PTT Enabled *PTT Disabled Audio Volume Bars Tone Volume Bars * Default setting **Option appears when Ring Cadence and Vibrate Cadence are both set to a value other than cOff d +These options are available only on the NetLink i640 Wireless Telephone SpectraLink Corporation Configuration and Administration 4NetLink e340/i640 Wireless Telephone Cisco CallManager and IP Phone 7960 Emulation 72-1082-02-G.doc Page 26 Main Menu Scroll through the list of options by pressing the Up and Down side buttons. Select an option by pressing the Select side button. Lock Keys Language Ring Options Phone Options System Info Extension ID Name CallManager IP Addr Push-to-talk [i640] OK Exit Lock Keys When enabled, the Keypad Lock option will lock the keypad immediately. If the keypad is locked, it may be unlocked by the end user pressing the Unlk softkey and then the # key. Language If the system supports multiple languages, the language option will list what languages are available. Select the language from the list. Ring Options The Ring Option allows the user to set the ring for three separate functions. Telephone ring is used for usual telephony functions. The Auxiliary Rings may be used to set different ringing patterns for OAI applications. Telephone Ring Auxiliary Ring 1 Auxiliary Ring 2 OK Up Telephone Ring Telephone Ring allows the user to set a distinctive ring style, volume and sequence. Select from an audible ring or a vibrate-only ring or a vibrate ring along with or followed by an audible ring. Ring Cadence Ring Tone Ring Volume [i640] Vibrate Cadence Ring Delay OK Up SpectraLink Corporation Configuration and Administration 4NetLink e340/i640 Wireless Telephone Cisco CallManager and IP Phone 7960 Emulation 72-1082-02-G.doc Page 27 Ring Cadence The cadence is the rhythm of the ring. It may be set to a pre- programmed ring cadence or it may be set to obtain its cadence from the Call Agent. The PBX option is designed to utilize any distinctive rings sent by the Call Agent while allowing the user to set unique rings for auxiliary applications. Off PBX Continuous Short Pulse Long Pulse OK Up Off : silent PBX : Call Agent determines ring cadence (e.g. the Call Agent may send rings that differentiate between internal and external calls.) Continuous : rings continually until answered Short Pulse : rings in short bursts Long Pulse : rings in long bursts Ring Tone select from five available tones (scroll to Tone 5 option). The Play softkey allows the user to preview the tone before selecting. If Ring Cadence is turned off, the Ring Tone option will not appear on the menu. Tone 1 Tone 2 Tone 3 Tone 4 Tone 5 OK Play Up Ring Volume (NetLink i640 Wireless Telephone only) The user may select a volume level by pressing the Up and Down side buttons and then pressing the OK softkey. The graduated volume bar indicates the levels. This setting may be overridden by adjusting volume while the handset is ringing. Vibrate Cadence Vibrate Cadence options are the same as for Ring Cadence Ring Delay Ring Delay determines how long the vibrate cadence will play before the audible ring starts. If Ring Cadence and Vibrate Cadence are turned off, the Ring Delay option will not appear on the menu. No Delay 5 Second Delay 10 Second Delay OK UP SpectraLink Corporation Configuration and Administration 4NetLink e340/i640 Wireless Telephone Cisco CallManager and IP Phone 7960 Emulation 72-1082-02-G.doc Page 28 Auxiliary Ring 1 and Ring 2 Auxiliary rings are designed to be utilized by OAI applications, enabling the user to set a distinctive ring for these applications. Phone Options Noise Mode Provides options that describe the noise level in your environment. Changing this mode to High or Severe adjusts the handset 9s microphone and in-ear speaker volume to account for background noise. Select Normal for most office environments; High for moderate background noise; or Severe for extremely noisy conditions. If you use High or Severe modes in a quiet environment, the person on the other end of the line may find it difficult to hear your voice. Key Tones Key tones may be turned on or off and determine if tones play when keys are pressed. Key tones are enabled by default. Warning Tones The handset plays various warning tones such as system up or down, out of range, etc. These tones may be turned on or off and are enabled by default. Display Contrast The display may need to be adjusted for different lighting situations. Contrast may be set by pressing the Up and Down side buttons until the desired contrast is displayed and then pressing the OK softkey. Keypad Autolock The handset may be set to lock the keypad automatically when in standby mode. The automatic locking function of the keypad may be disabled (the default) or adjusted for a 5, 10 or 20 second delay before locking. System Info Phone IP Addr Displays the IP address currently assigned to the handset. Firmware Version displays the software version running the handset. The MAC address is the hardware identification number and is set at the factory. Three code numbers correspond to the three files that each version uses. (MAC address) (downloader code) (functional code) (phintl file) OK Up Downloader: pd11gl3.bin Functional: pd11skd3.bin Phintl: pi110001.bin Extension Displays the extension currently assigned to the handset. ID Name The ID Name permits an alphanumeric entry that will appear on the standby display under the extension number. The entry technique uses cell phone style entry where the key is pressed repeatedly to scroll through the characters for that key, starting with the letter characters. Enter up to 16 characters. CallManager IP Addr This option displays the IP Address currently assigned to the CallManager. Push-to-talk The NetLink i640 Wireless Telephone incorporates PTT functionality. PTT may be allowed or disallowed in the Admin menu. If allowed, the user may enable or disable locally, and may set the channel, tone volume and audio volume. SpectraLink Corporation Configuration and Administration 4NetLink e340/i640 Wireless Telephone Cisco CallManager and IP Phone 7960 Emulation 72-1082-02-G.doc Page 29 The menu for push-to-talk does not appear if PTT is disallowed on the Admin menu or if no channel is enabled on the Admin menu. Channel Enable/Disable Audio Volume Tone V olume OK Up Channel The user may enable any PTT channel that has been allowed in the Admin menu by entering the corresponding number from the keypad. If PTT has been enabled in this handset, the default channel is the lowest allowed channel as set in the Admin menu. Current Channel: X 1 2 3 4 5 6 7 8 New Channel = ? Up Enable/Disable The user may enable or disable PTT on this handset. PTT is disabled by default. PTT Enabled PTT Disabled OK Up Audio Volume, Tone Volume The user may select volume levels by pressing the Up and Down side buttons and then pressing the OK softkey. The graduated volume bar indicates the levels. The Audio Volume setting may be overridden by adjusting volume while the handset is in a push-to-talk call. If PTT is allowed in the Admin menu and enabled by the user, Battery Pack life when the handset is in standby mode is decreased to about 30 hours. (Additional options may be present. Contact your system administrator for information.) SpectraLink Corporation Configuration and Administration 4NetLink e340/i640 Wireless Telephone Cisco CallManager and IP Phone 7960 Emulation 72-1082-02-G.doc Page 30 5. License Management NetLink Wireless Telephones support a number of different IP protocol integrations. All NetLink e340/i640 Wireless Telephones are shipped from SpectraLink with a generic software load that allows them to associate to a wireless LAN and download their functional software from a TFTP server. The handsets will not function properly without downloading appropriate software. The following details the process to properly configure NetLink e340/i640 handsets and download software via over-the-air file transfer. 5.1 Requirements " A wireless LAN must be properly configured and operational through the use of 802.11b wireless APs. " Cisco 9s CallManager (Release 3.08 or greater) must also be connected to your network and completely operational. " A TFTP server must be available on the network in order to load the appropriate software into the handsets. Most installations choose to take advantage of the TFTP server that accompanies the CallManager, making a separate TFTP server unnecessary. " Finally, ensure that the Battery Pack on the handset is fully charged. 5.2 Configuration Process 1. Download the latest NetLink e340/i640 Wireless Telephone IP software from http://www.polycom.com/usa/en/support/voice/wi-fi/wi-fi.html . Scroll to NetLink e340/i640 3 Cisco; Cisco SCCP 3 7960 emulation and click the hyperlink to start the download. 2. Load the latest version of the SCCP code and place it on the TFTP server and ensure the TFTP server is started. The five files that are needed must be named: slnk_cfg.cfg pd11gl3.bin pd11skd.bin pd11skd3.bin pi110001.bin 3. If statically assigning IP addresses, ensure that the Phone IP address, TFTP server IP, Subnet Mask, and Default Gateway information are accurate in the Admin menu. If using a DHCP server, ensure that appropriate options are set for the TFTP server. See the NetLink Wireless Telephone Configuration section for detailed configuration instructions. 4. Ensure the handset has properly configured ESSID and Reg Domain Information within the Admin menu. If you are accepting broadcast ESSIDs at your APs, the handset will automatically learn the ESSID information when powering on. See NetLink Wireless Telephone Configuration section for detailed configuration instructions. SpectraLink Corporation Configuration and Administration 4NetLink e340/i640 Wireless Telephone Cisco CallManager and IP Phone 7960 Emulation 72-1082-02-G.doc Page 31 5. Using the Admin menu on the handset, ensure the License Option menu option is set to 008 . This ensures the handset will check for the proper SCCP files each time it powers on. See NetLink Wireless Telephone Configuration section for detailed configuration instructions. 6. Ensure security settings are properly programmed. See section 3 NetLink Wireless Telephone Configuration for detailed configuration instructions. 7. Exit the Admin menu. 8. The SCCP code will now download to the handset. The status bar will increment fully across the display for each function that is being performed in the download process. Upon completion of the update process, the handset will re- boot with the new firmware. 9. Register the handset with CallManager (if auto-register is not enabled) and properly label the handset with the appropriate extension. For future software upgrades, simply update the files that are stored on the TFTP server. Each time the handset is powered up, it will check with the TFTP server to ensure it has the proper software version. SpectraLink Corporation Configuration and Administration 4NetLink e340/i640 Wireless Telephone Cisco CallManager and IP Phone 7960 Emulation 72-1082-02-G.doc Page 32 6. CallManager Integration Factors This section describes the mapping between the emulated Cisco IP Phone 7960 and the NetLink e340/i640 Wireless Telephone. Voice messaging access Voicemail access is obtained through the message key which is accessed on the handset as FCN + a digit that corresponds to the assigned button on the CallManager template is identified as Voice Mail. See Section 7 Feature Programming for information on assigning feature buttons. CODECs The NetLink e340/i640 Wireless Telephone is compatible with the G.711 and G.729a/ab codecs. There is no setting required on the handset. DHCP Dynamic Host Configuration Protocol (DHCP) is a standardized protocol that enables clients to be dynamically assigned with various configuration parameters, such as an IP Address, subnet mask, default gateway, and other critical network configuration information. DHCP servers centrally manage such configuration data, and are configured by network administrators with settings that are appropriate for a given network environment. The handset will use the following DHCP options if DHCP use is enabled: Option Meaning 1 Subnet mask 3 Default gateway 6 DNS server 15 Domain name 66 TFTP server 150 Cisco TFTP server 151 NetLink SVP Server 152 NetLink OAI Gateway siaddr Boot server or next server TFTP All Cisco CallManager IP telephony clients receive their configuration information from the CallManager TFTP server. The NetLink e340/i640 Wireless Telephone matches this behavior, using TFTP to receive its configuration information from the CallManager. It can also use TFTP to update the handset software over the 802.11b wireless LAN. DNS Domain Name System (DNS), an industry-standard protocol, locates computers on an IP-based network. IP networks rely on number-based addresses to move information on the network. However, users are better at remembering friendly SpectraLink Corporation Configuration and Administration 4NetLink e340/i640 Wireless Telephone Cisco CallManager and IP Phone 7960 Emulation 72-1082-02-G.doc Page 33 names than number-based addresses, so, it is necessary to translate user-friendly names into addresses that the network can recognize. The handset will use DNS to automatically translate names into IP Addresses for these components: TFTP server, NetLink SVP Server, and the Cisco TFTP server. CallManager fail-over Cisco recommends that CallManager be implemented in cclusters d that will load- balance as well as provide a fail-over mechanism. The NetLink e340/i640 Wireless Telephone has the ability to tolerate the failure of the CallManager it has registered with just as a Cisco IP Phone would. SRST The NetLink e340/i640 Wireless Telephone is compatible with SRST. SpectraLink Corporation Configuration and Administration 4NetLink e340/i640 Wireless Telephone Cisco CallManager and IP Phone 7960 Emulation 72-1082-02-G.doc Page 34 7. Feature Programming The NetLink e340/i640 Wireless Telephone emulates the Cisco IP Phone 7960. All telephone functions and messaging features are supported if possible. Functions that require the use of the volume keys, speakerphone functions, and services settings are not supported. The handset uses cshortcut keys d to emulate the feature keys on the 7960. Pressing LINE , FCN , or MENU plus a shortcut key will activate the assigned line appearance or feature. In the standby mode, the handset has four display rows. The top row displays the signal strength icon, line numbers, a voicemail icon if there is a message waiting or a downloader icon if the handset is downloading code, call icons, arrow icons, and the battery icon. The second row displays the extension and identity of the handset as assigned by the CallManager. The third row displays identification information as set in the Standby menu. If the handset has been forwarded or is on hold, the third row will cycle through the ID, forwarding, and hold information. The bottom row displays the time and date as received from the CallManager. SpectraLink Corporation Configuration and Administration 4NetLink e340/i640 Wireless Telephone Cisco CallManager and IP Phone 7960 Emulation 72-1082-02-G.doc Page 35 7.1 Feature Assignment In CallManager, Line keys 1-4 may be assigned to line appearances or to speed dial numbers. Line appearances are displayed on the handset in the Line Appearance List. Speed dial numbers are displayed in the Function List. The Mute, Voicemail and OAI features are assigned to a function key sequence as described below. These features are displayed in the handset Function List. All other features are assigned to the softkeys. The softkeys on the NetLink e340/i640 emulate the softkeys on the Cisco 7960 deskset. If an Open Application Interface (OAI) is operational, a function key sequence will be assigned in the OAI configuration. Any sequence(s) utilized by OAI will have priority in the Function display list. The other functions assigned to this list will appear in this order: Mute, Voicemail, speed dial numbers. E.g. If OAI is assigned to FCN 3 and FCN 6 , then Mute will be FCN 1 , Voicemail will be FCN 2 , and speed dial numbers will be FCN 4 , 5 , 7 , 8 , and so on. SpectraLink Corporation Configuration and Administration 4NetLink e340/i640 Wireless Telephone Cisco CallManager and IP Phone 7960 Emulation 72-1082-02-G.doc Page 36 7.2 Feature Access All features are viewed with the handset off hook. Press the Start

less