Fasteners and screw threads

threads to mate with internal screw threads tapped with tolerance position H or G after galvanizing ISO 965-5:1998 ISO general purpose metric screw threads 4 Tolerances 4 Part 5: Limits of sizes for internal screw threads to mate with hot-dip galvanized external screw threads with maximum size of tolerance position h before galvanizing ISO 1502:1996 ISO general-purpose metric screw threads 4 Gauges and gauging 2.2 Technical drawings for screw threads and threaded parts ISO 5845-1:1995 Technical drawings 4 Simplified representation of the assembly of parts with fasteners 4 Part 1: General principles Fasteners and screw threads, Ed. 5, Vol. 1 Page 2 of 3 ISO 6410-1:1993 Technical drawings 4 Screw threads and threaded parts 4 Part 1: General conventions ISO 6410-2:1993 Technical drawings 4 Screw threads and threaded parts 4 Part 2: Screw thread inserts ISO 6410-3:1993 Technical drawings 4 Screw threads and threaded parts 4 Part 3: Simplified representation 2.3 Special screw threads ISO 1478:1983 Tapping screws thread 2.4 Variations of forms, dimensions and designation ISO 225:1983 Fasteners 4 Bolts, screws, studs and nuts 4 Symbols and designations of dimensions ISO 272:1982 Fasteners 4 Hexagon products 4 Widths across flats ISO 273:1979 Fasteners 4 Clearance holes for bolts and screws ISO 885:2000 General purpose bolts and screws 4 Metric series 4 Radii under the head ISO 888:1976 Bolts, screws and studs 4 Nominal lengths, and thread lengths for general purpose bolts ISO 3508:1976 Thread run-outs for fasteners with thread in accordance with ISO 261 and ISO 262 ISO 4753:1999 Fasteners 4 Ends of parts with external metric ISO thread ISO 4755:1983 Fasteners 4 Thread undercuts for external metric ISO threads ISO 4757:1983 Cross recesses for screws ISO 7378:1983 Fasteners 4 Bolts, screws and studs 4 Split pin holes and wire holes ISO 7721:1983 Countersunk head screws 4 Head configuration and gauging ISO 7721-2:1990 Countersunk flat head screws 4 Part 2: Penetration depth of cross recesses ISO 8991:1986 Designation system for fasteners ISO 10664:1999 Hexalobular internal driving feature for bolts and screws 2.5 Tolerances of fasteners ISO 4759-1:2000 Tolerances for fasteners 4 Part 1: Bolts, screws, studs and nuts 4 Product grades A, B and C ISO 4759-3:2000 Tolerances for fasteners 4 Part 3: Plain washers for bolts, screws and nuts 4 Product grades A and C 2.6 General requirements and mechanical properties of fasteners ISO 898-1:1999 Mechanical properties of fasteners made of carbon steel and alloy steel 4 Part 1: Bolts, screws and studs ISO 898-2:1992 Mechanical properties of fasteners 4 Part 2: Nuts with specified proof load values 4 Coarse thread Fasteners and screw threads, Ed.<br><br> 5, Vol. 1 Page 3 of 3 ISO 898-5:1998 Mechanical properties of fasteners made of carbon steel and alloy steel 4 Part 5: Set screws and similar threaded fasteners not under tensile stresses ISO 898-6:1994 Mechanical properties of fasteners 4 Part 6: Nuts with specified proof load values 4 Fine pitch thread ISO 898-7:1992 Mechanical properties of fasteners 4 Part 7: Torsional test and minimum torques for bolts and screws with nominal diameters 1 mm to 10 mm ISO 2320:1997 Prevailing torque type steel hexagon nuts 4 Mechanical and performance properties ISO 2702:1992 Heat-treated steel tapping screws 4 Mechanical properties ISO 3506-1:1997 Mechanical properties of corrosion-resistant stainless-steel fasteners 4 Part 1: Bolts, screws and studs ISO 3506-2:1997 Mechanical properties of corrosion-resistant stainless-steel fasteners 4 Part 2 : Nuts ISO 3506-3:1997 Mechanical properties of corrosion-resistant stainless steel fasteners 4 Part 3: Set screws and similar fasteners not under tensile stress ISO 4042:1999 Fasteners 4 Electroplated coatings ISO 6157-1:1988 Fasteners 4 Surface discontinuities 4 Part 1: Bolts, screws and studs for general requirements ISO 6157-2:1995 Fasteners 4 Surface discontinuities 4 Part 2: Nuts ISO 6157-3:1988 Fasteners 4 Surface discontinuities 4 Part 3: Bolts, screws and studs for special requirements ISO 7085:1999 Mechanical and performance requirements of case hardened and tempered metric thread rolling screws ISO 8839:1986 Mechanical properties of fasteners 4 Bolts, screws, studs and nuts made of non-ferrous metals ISO 8992:1986 Fasteners 4 General requirements for bolts, screws, studs and nuts ISO 10666:1999 Drilling screws with tapping screw thread 4 Mechanical and functional properties ISO 10683:2000 Fasteners 4 Non-electrolytically applied zinc flake coatings 2.7 Testing and acceptance inspection ISO 3269:2000 Fasteners 4 Acceptance inspection ISO 3800:1993 Threaded fasteners 4 Axial load fatigue testing 4 Test methods and evaluation of results ISO 8749:1986 Pins and grooved pins 4 Shear test ISO 10484:1997 Widening test on nuts ISO 10485:1991 Cone proof load test on nuts ISO 15330:1999 Fasteners 4 Preloading test for the detection of hydrogen embrittlement 4 Parallel bearing surface method

less