ToyoTa Tundra sTepside insT

To view this page ensure that Adobe Flash Player version 9.0.124 or greater is installed.

Please login or register to make a comment!

ToyoTa Tundra sTepside insTallaTion insTrucTions Read your owner 9s manual and these instructions before installing your Toyota Tundra Truxedo ® kit. Follow these instructions to install your TruXedo ® side rail clamps and adapter pan. Side rails are notched and pre-bent to conform to your pickup bed.

1 1703482 Clamp w/Slot, Male 2 1115184 Clamp, Female, Lo Pro 3 1700429 Flat Washer, 3/8 d 4 1700369 Cap Screw, 3/8 d x 1 3/4 d 5 1115745 Plastic Washer, 1/4 d x 1 1/2 d 6 1701580 Nylon Lock Nut, 3/8 d Item Part # Description 2 1 clamp assembly 4 3 5 6 ___ 1 ___ STEP 1: A 1/4 d x 6 d piece of seal is provided to (ll the gaps near the bulkhead. This seal should be applied BEFORE the side rails are attached. The following pictures are shown with the side rails attached to illustrate the proper placement of the seal.

Cut seal to (t (approx. 4 d) and place along the area marked by x 9s in the photo below. (Photos shown are of the TruXedo Lo Pro QT.

The rails will look different but placement of the seal is the same.) bulkhead top view rail xxxxxxxx xxxxxxxxxxx ... more. less.

Add seal to areas marked by x 9s gap STEP 2: Cut another piece of seal and af(x it to area marked by x 9s in the photo below. xxxxxxxx Add seal to areas marked by x 9s 1/4 d seal added top view side view bulkhead rail rail bulkhead P/N 1114881 Rev. F T f"X 7 6 d, i c 5. P.O. Box 1078, 2209 Kellen Gross Dr., Yankton, South Dakota 57078 Call Toll Free: 1-877-TRUXEDO (1-877-878-9336) Fax: (605) 664-9304 V 9 9t u o c a 9 c 7: htt e://www.t f"x 7 6 d. 5 dm P/N 1114881 Rev. F ToyoTa Tundra sTepside insTallaTion insTrucTions conTinued STEP 3: Position clamps 9 d and 36 d from front of box; and 8 d and 17 d from tailgate (four clamps per side rail). STEP 6: Center pan adapter on front header. Fasten 3/8 d x 3/4 d stove bolts through holes in pan adapter and into square nuts inside header slot. Tighten bolts. square nut, 3/8 d front header cover STEP 5: Align side rails 1/4 d from tailgate, )ush with bed rail and level with each oth- er. Tighten clamp assemblies (see owner 9s manual). noTe: Refer to owner 9s manual for cover installation. assemble & install adjustable clamp as shown stove bolt, 3/8 d x 3/4 d clamp adapter pan STEP 4: Clamp side rails to pickup bed at locations shown. 1/4 d tailgate side rail bed rail 36 d 9 d 8 d 17 d front of box clamp tailgate spring plunger screw in front header front header & cover assembly (cover not shown for clarity) plastic washer lock nut, 3/8 d slot in side rail T f"X 7 6 d, i c 5. P.O. Box 1078, 2209 Kellen Gross Dr., Yankton, South Dakota 57078 Call Toll Free: 1-877-TRUXEDO (1-877-878-9336) Fax: (605) 664-9304 V 9 9t u o c a 9 c 7: htt e://www.t f"x 7 6 d. 5 dm ___ 2 ___ STEP 7: Front header: Back spring plunger out. Set cover assembly across cab end of side rails. Insert screws in front header through slots in side rails. Secure with plastic washers and lock nuts, but do not over tighten. Header must be free to slide.

less