WIRE CONNECTIONS MUST BE SEALED IF USED INAWET LOCATION. WATER MAY TRAVEL UPAN UN-SEALED WIREAND CAUSE CORROSION PROBLEMS.<br><br> +12V WIRING DIAGRAM 1 WIRING DIAGRAM 2 PRESSING PATTERN SELECTWILLINCREMENT THE FLASH PATTERN. PRESSAND HOLD PATTERN SELECT WHILE TURNING THE POWER SWITCH ON TO RESET FLASH PATTERN TO #1. CONNECTION TO FLASHER - GND BLACK ON/OFF SWITCH RED FUSE 5A - GND BLACK RED TOADDITIONAL LIGHTS...<br><br> - GND BLUE BLUE TOUCH BLUE TO +12V (RED)TO CHANGE FLASH PATTERN BASIC WIRING WITH SIMPLE ON/OFF SWITCH ON/OFFAND FLASH PATTERN SELECTION +12V - GND BLACK ON/OFF SWITCH RED FUSE 5A - GND BLACK RED TOADDITIONAL LIGHTS... - GND BLUE BLUE PATTERN SELECTSWITCH ISAMOMENTARY, NORMALLYOFF, PUSHBUTTON SWITCH. PATTERN SELECT TOADDITIONAL LIGHTS...<br><br> FLASH PATTERN LIST +12V - GND BLACK ON/OFF SWITCH RED FUSE - GND BLACK RED - GND BLUE BLUE The LEDWIC3 can be driven by any lamp flasher or LED flasher that is made to drive +12 Volt lamps or LED heads. SETTHE LEDWIC3TO PATTERN 1 WHEN USING WITH FLASHER STEADY ON The easiest way to set the LEDWIC3 to steady on mode is to temporarily twist BLUE and RED together and apply power. Then, tie BLUE to the BLACK wire to ensure that the flash pattern will never change from steady on mode.<br><br> FLASHER FOLLOW FLASHER INSTALLATION SHEET FOR CONNECTION OF POWER AND ON/OFF SWITCH. - GND OUTPUT OUTPUT CONNECTBLUETO BLACK WIRE ONLYAFTER SETTINGTHE HEADSTO STEADYON MODE. Patterns 3 through 7 and 13 through 15 split the LED array into two halves .<br><br> The remaining patterns flash the entire LED array. RANDOM mode picks from both split and full array flash patterns. # Flash Pattern Description 1 Steady ON All LEDs on.<br><br> FOR USE WITH EXTERNAL FLASHER ONLY. 2 RANDOM Randomly selects from patterns 3 through 13 and runs each pattern 10 times. 3 Double Flash - SPLIT 2 Flash Bursts Alternating between split LED array.<br><br> 115 Double FPM. 4 Quad Flash - SPLIT 4 Flash Bursts Alternating between split LED array. 140 Quad FPM.<br><br> 5 Mega Flash - SPLIT 1 Flash Burst Alternating between split LED array. 500 FPM. 6 Phased Mega - SPLIT 1 Flash Burst Alternating between split LED array.<br><br> Varies from 360 to 1200 FPM. 7 Deciblast - SPLIT 10 Flash Bursts Alternating between split LED array. 170 Deci FPM.<br><br> 8 Double Flash 2 Flash Bursts. All LEDs firing.115 Double Flashes Per Minute. 9 Quad Flash 4 Flash Bursts.<br><br> All LEDs firing. 140 Quad Flashes Per Minute. 10 Mega Flash 1 Flash Burst.<br><br> All LEDs firing. 500 Flashes Per Minute. 11 Phased Mega 1 Flash Burst.<br><br> All LEDs firing. Varies from 360 to 1200 Flashes Per Minute. 12 Deciblast 10 Flash Bursts.<br><br> All LEDs firing. 170 Deci Flashes Per Minute. 13 Flasher - SPLIT Wig-Wag Flasher pattern split across LED array.<br><br> 3 Flashes per second rate. 14 Flasher Sequence 1 - SPLIT Wig-Wag and Steady Flasher sequence 1. 3 Flashes per second rate.<br><br> 15 Flasher Sequence 2 - SPLIT Wig-Wag and Steady Flasher sequence 2. 3 Flashes per second rate. SEALING WIRE CONNECTIONS RTV 22-18 BUTT-SPLICE SOLDERED HEATSEALED BUTT-SPLICE 22-18 OR ELECTRICALTAPE WILLNOTSEALACONNECTION<br><br>

less