the front axle. Handy controls ... so handy you feel at ease the first time you get behind the wheel.<br><br> I Farmall C tractor adjustable front axle range is from 56 to 89% inches (special). Rear tread adjustments from 47 to 80 inches. Special axles give treads of 88 or 100 inches.<br><br> 221/2 inches is the clearance you have with a Farmall C equipped with adjustable wide tread front axle. The Farmall C tractor is easy to operate. Controls are close together, placed near hands or feet for convenient oper- ation.<br><br> 5 FARMALL TRACTOR FEATURES for Easier, Faster Truck Fermin 6 FARMALL C 1 Universal Mounting Frame All front - mounted implements slip right in position on the Uni- versal Mounting Frame. Just tighten or loosen without remov- ing nuts ... no chance of losing them.<br><br> Time required is 6 to 7 minutes. 2 Tractor Mounting Pads These pads have tapped holes for attaching hopper units as well as attaching the Universal Mounting and Hitching Frames. Tapered bolts and bracket slots assure accurate and rigid locking.<br><br> 3 Plow Hitch This hitch makes it quick and easy to attach plows. and remove moldboard FARMALL CUB 1 Universal Mounting Frame All forward-mounted cultivators and planters attach to a Universal Mounting Frame. Parallel action of the frame keeps the ground tools always at the same pitch, regardless of operating depth.<br><br> Implements attach easily and quickly (average time 61/2 min- utes) and to quick-hitch keyhole slots. 2 Tractor Mounting Pads Tractor mounting pads hold the forward-mounted planter hop- pers firmly in place. The hopper frame has slotted brackets with tapered holes which match the taper on the underside of the bolt heads.<br><br> 3 Reversible Drawbar To reverse the drawbar, all you do is loosen four tapered bolts. The drawbar can be set to pivot, or it can be adjusted to three fixed posi- tions. It is used for rear-mounted and trailing implements.<br><br> FARMALL SUPER-A 1 Universal Mounting Frame You attach all front -mounted implements to the Universal Mounting Frame. Just tighten or loosen two taper-faced nuts on the tool bar, then slip the imple- ment in or out of the keyhole slots. ( Time is 6 1 ,4 minutes aver- age.<br><br> ) 2 Tractor Mounting Pads Taper-faced cap screws hold the slotted slip-on hopper brackets in exactly the same position when- ever you remove and then re- place them again. The tapered holes match the tapered cap screws. 3 Reversible Drawbar Just loosen, then retighten, four bolts to reverse the drawbar.<br><br> Attach rear-mounted or pull-type implements to it. Adjust it to four fixed posi- tions, or set it to pivot and to be controlled from the tractor seat when in forward position. 7 no longer necessary to tug and heave at heavy, awkward levers.<br><br> Now, just drop your hand from the steering wheel to convenient Farmall Touch- Control. A "fingertip-touch" on a pencil-sized lever instantly raises, lowers and holds, plant- ers, cultivators, and other trac- tor-mounted implements .Two- way hydraulic power does the work 4whether the tractor is moving or standing still. You save time and energy .<br><br> . . and do better work.<br><br> The Farmall Cub has one Touch-Control lever which is used for raising, lowering, or adjusting both front- and rear- mounted equipment. A Master manual control lever is avail- le m " , e_";- _Mu ,u,_1. " fQr the Farmall Cub.<br><br> The Farmall Super-A has two control levers which operate three power arms 4two in uni- son and one individually. You can control rear-mounted equipment independently of front-mounted equipment. Likewise, independent control of right and left implement sections is possible.<br><br> Like the Farmall Super-A, the Farmall C has two control levers which make possible the separate control of forward- and rear-mounted implement sections as well as independent control of right- and left-hand forward-mounted implement sections. With the Farmall C it is just a matter of aiming the radiator cap at the marker furrow. On the bed, of course, it is even simpler than that.<br><br> 7 Culti-Vision is a design feature r which gives you a clear view of the rows, and the machines at work. You have a clear view to the front, to both sides, and to the rear. When planting with the Farm- all Cub or Farmall Super-A, as shown here, you simply aim the guide rod on the tractor at the shallow furrow created by the marker.<br><br> ONTR Saves Work CUL SION Saves Time and Plants Formal! Cub tractor, with ad- justable front axle and Farmall Touch-Control, is shown plant- ing onions in 12-inch rows with the Cub-474, four-row, for- ward-mounted planter. Note the perfectly uniform pressure exerted by each of the press wheels.<br><br> Farmall Cub tractor, with ad- justable front axle and Farmall Touch-Control, is shown plant- ing peas in 22-inch rows with the Cub-435 four-row, rear- mounted planter. Notice that there are two rows inside and two outside the wheel treads. 1 0 Farmall Super-A tractor, with adjustable front axle and Farmall Touch-Control, is shown planting three rows of kohl- rabi in 24-inch rows, with the A-674, six-row, forward- mounted planter.<br><br> This operator plants his crops in five 12-inch or three 24-inch rows. For 24- inch rows he changes to single seed spouts and drops off two of the planter units. Farmall Super-A tractor, with adjustable front axle and Farmall Touch-Control, is shown planting four rows of onions in 20-inch rows.This rear-mounted planter may be ordered with 4- or 6-row units, depending on the row spacing requirements of the user.<br><br> 2 Farmall C, with adjustable wide front axle and Farmall Touch- Control, is shown planting rad- ishes in 12-inch rows with the C-674, 6-row, forward-mounted planter. This planter adapts it- self ideally to 12- and 24-inch rows by dropping off three planter units and changing to single seed spouts. Farmall C tractor, with adjust- able wide front axle and Farm- all Touch-Control, is shown planting carrots in 12-inch rows, with the C-635 rear- mounted, direct-connected planter.<br><br> This planter and the forward-mounted cultivator fit on the tractor at the same time. This highly efficient unit makes it possible to plant or cultivate without disturbing either im- plement. 14 Formal!<br><br> Cub tractor, with ad- justable front axle on the front and six-inch tires on the rear, is shown working six rows of very small spinach with the Cub-447 forward-mounted cul- ,7- tivator equipped with 9-inch disk weeders and duckfoots. In this operation not a single plant was buried. Formal!<br><br> Cub tractor shown with adjustable front axle and rear wheels set to 40-inch tread. Forward-mounted on the trac- tor is the Cub-252 two-row beet and bean cultivator equipped with diamond points on the front and 12-inch high-wing furrowers on the rear. This unit is reopening irrigation furrows and cultivating narrow, two- row beds of turnips.<br><br> 18 Farmall Super-A with Farmall Touch-Control is shown with adjustable front axle and rear wheels set to 68 inches. The A- 647 six-row, forward-mounted cultivator is working, inside the wheel treads, six rows of car- rots that have just come through the ground. Knife weeders and duckfoots are the ground tools.<br><br> Farman Super-A tractor is shown with the A-452 beet and bean cultivator working in young peas. This unit is "fast on its feet" and will cover plenty of ground in a single day. 20 Farmall C is shown with the C-647 six-row cultivator for- ward-mounted on the tractor, working in broccoli planted on the bed in 12-inch rows.<br><br> Later in the growing season these same plants will be trans- planted to the field. This is the Farmall C tractor with the C-452 beet and bean cultivator working in two nar- row beds of lettuce. Notice that the operator has equipped the tractor with the single front wheel.<br><br> The wide front axle would work equally as well. 22 " " " " PARTS mccoRm[cK-DFFRIN/ " The IH Dealer Serves You in 3 Ways FIRST, in his attractive place of business the IH dealer displays and stocks a full line of modern tractors and " farm equipment suitable for use in your locality. He knows the crops you grow, the soil and climatic conditions you must contend " with, the farming methods you prefer 4 and he arranges to supply " you with just the types and sizes of machines and attachments you need to perform your seasonal operations quickly, efficiently, and " at minimum cost.<br><br> He is experienced and well-informed. He stands " ready to discuss your production problems and to demonstrate, " on your own acres, any equipment in which you are interested. He is a farm equipment specialist whom it will pay you to consult.<br><br> SECOND, the IH dealer stocks and supplies all commonly needed replacement parts for the machines he sells and can supply the less commonly needed parts on short notice. He sells only " genuine International Harvester engineered parts 4 made to exactly " the same specifications as the original parts in the machine. Parts " men are alert, obliging, and competent, ready to supply you with whatever part or accessory you need.<br><br> In facilities and personnel " the IH dealer spares no effort or expense to have on hand the " parts you need at the moment you need them. Delays due to the breakage or wearing-out of parts seldom occur when your equip- ment carries the IH monogram. EQUIPMENT PARTS SERVICE THIRD, the up-to-date IH dealer maintains a well-equipped, competently staffed service station in which any type of " farm equipment, from tractors and combines to disk harrows and cream separators, can be reconditioned, repaired, or overhauled " according to the high standards of the Blue Ribbon Service code.<br><br> " He places at your disposal a large investment in shop space, tool " equipment, and skilled personnel in order that your farm tractors and machines may be maintained in first-class operating condition. Avail yourself of the opportunity to keep your equipment in top- notch condition by having it repaired or overhauled 4before the season of use 4in the service station of your local IH dealer. INTERNATIONAL HARVESTER lir1P NTERNATI NA - "H R Co ARVES 180 NORTH MICHIGAN AVE.<br><br> CHICAGO 1, ILLINOIS, U.S.A. A-103-MM. 1-10.<br><br> Lithographed in United States of America.

less